08-02-2010
Linux and IPv6
Hi gurus,
In a few month, we must enable IPv6 on our Linux Server!
Should we reinstall the Linux machine to enable IPv6 or could we just make some change in configuration's files?
Could Linux run simultaneous IPv4 and IPv6?
Thanks in advance for our help our ideas?
Best regards,
nm
9 More Discussions You Might Find Interesting
1. IP Networking
Hi everyone,
I have a weird problem in Linux. Well, for the past month i've been very interested in IPv6, and, a couple of days ago i decided to try to get it to work. I run Slackware 8.0 on my gateway/router-box, and, the freenet6.com-program and scripts started and worked just fine. There's one... (1 Reply)
Discussion started by: kuba
1 Replies
2. IP Networking
Hello guyz..
did some of u have implement or making a testbed for IPv6?
if yes, can u attached the procedures and standard guidelines because i really need for my proposal..
thanx.. (2 Replies)
Discussion started by: unknown2205
2 Replies
3. Linux
how to enable an ipv6 address on a linux pc?
thanks in advance (3 Replies)
Discussion started by: sunittaneja
3 Replies
4. Linux
I am trying to capture the ipv6 packets through pcap utility.
For that i am redirecting the ipv6 packets to the loopback address , but the ipv6 packets are not getting redirected to tha loopback address.Instead they are taking there normal routes. (1 Reply)
Discussion started by: vikasmca05
1 Replies
5. AIX
Hi Every1,
I want to configure IPv6 on AIX and want to communicate between IPv4 machine IP and IPv6 machine. Is it possible? (2 Replies)
Discussion started by: Shrek
2 Replies
6. Linux
Hi,
Can any one please help me increase the arp stale time of an ipv6 interface on linux platform ?
I have tried increasing the variable gc_stale_time but that doesnt work.
Thanks (2 Replies)
Discussion started by: dkothapa
2 Replies
7. IP Networking
Well I cannot be too certain of the setup, since it's a stock firmware, but I have a cheap Belkin wireless-n router and wanted to get some ideas of what may be going on while I've a few moments to ramble on about my problems... I requested the GPL source so I've just been pondering while waiting to... (0 Replies)
Discussion started by: neutronscott
0 Replies
8. UNIX for Dummies Questions & Answers
Hi,
I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies
9. IP Networking
I am trying to setup an IPv6 network.
I modified the interfaces file:
/etc/network/interfaces
# The loopback network interface
auto lo
iface lo inet loopback
iface etho0 inet static
address 2620:7:a000::1
netmask 64
gateway ::ffff:c0a8:101
... (0 Replies)
Discussion started by: Meow613
0 Replies
mip6d(1) Mobile IPv6 and NEMO Daemon mip6d(1)
NAME
mip6d - UMIP Mobile IPv6 and NEMO Basic Support protocol implementation
SYNOPSIS
mip6d [options]
DESCRIPTION
Mobile IPv6 and NEMO Basic Support implementation
OPTIONS
-V, --version
Display version information and copyright
-?, -h, --help
Display this help text
-c <file>
Read configuration from <file>. If option is not present, default path (/etc/mip6d.conf) is used.
These options override values read from config file:
-d <number>
Set debug level (0-10)
-C, --correspondent-node
Node is CN
-H, --home-agent
Node is HA
-M, --mobile-node
Node is MN
SIGNALS
The following signals can be sent to the daemon:
SIGHUP
Reload the configuration. See mip6d.conf(5) for information on supported option reload.
SIGINT, SIGTERM
Terminates the daemon operation.
FILES
/etc/mip6d.conf
SEE ALSO
mip6d.conf(5), mipv6(7),
RFC6275: Mobility Support in IPv6
RFC3776: Using IPsec to Protect Mobile IPv6 Signaling Between Mobile Nodes and Home Agents
RFC4877: Mobile IPv6 Operation with IKEv2 and the Revised IPsec Architecture
RFC3963: Network Mobility (NEMO) Basic Support Protocol
May 16, 2005 mip6d(1)