NIM Issue Post: 302441342

10 More Discussions You Might Find Interesting

1. AIX

Nim Issue

Hi Guys.. Got a NIM issue.. Am trying to pull a image of a client from NIM server. am getting the following error... in standard error output.. 0042-001 nim: processing error encountered on "master": Usage: rm File... Am using the same script to pull image and it works fine.....

2. AIX

migrate NIM server through NIM installation

I try to migrate a NIM server from one server to another. I try to do a mksysb on NIM server restore the NIM server's mksysb to a client through NIM installation shutdown NIM server start newly installed client as NIM server Does anyone do this before? who can give me some suggestion?

3. AIX

NIM Server Issue

Hi, I'm getting the above error while trying to take a MKSYSB image via NIM. I've only just started getting this and don't know why it is failing. Any one got any suggestions? Thanks Kees

4. AIX

Nim

Hello guys, what is a sure-shot single command to find out if the NIM environment is working properly from both master as well as client side?

5. AIX

Nim

Hello everyone I have two questions. 1.-The NIM and EZNIM are the same. 2.-If I have in one partition NIM installed I need to install EZNIM or I need to unistall NIM and then install EZNIM. Thanks for your comments.

6. AIX

NIM master-client connectivity issue

Hello All, I believe my NIM master is fine. lsnim and cat /etc/niminfo gives me the right output. While doing "lsnim" on a client machine, I get ksh:lsnim:"not found". Please someone be nice enough to explain what are the steps to verify the master and client connectivity to do all the NIM...

7. AIX

Back up a client NIM from nim master

Hello everyone Im trying to backup a nim client from nim master but I got this message COMMAND STATUS Command: failed stdout: yes stderr: no Before command completion, additional instructions may appear below. 0042-001 nim:...

8. AIX

NIM : remove nim client info from the client

Hi. I change my client's IP and hostname but I forgot to change anything on the master. How can I redefine or modify my client's resource from my master, or with using smit niminit from my client ? Tks

9. AIX

Problem in communication nim client with nim master

Hello, I have an AIX6.1 machine which is a nim client to my nim master which is also AIX6.1 machine. I had some problem to perform an installation on my client using smit nim . i removed /etc/niminfo file in order to do the initialization again but when i run the command niminit -a name=client...

10. AIX

How to know NIM name from NIM client?

Friend's, I was playing around with NIM in my environment & had a quick question in mind which I didn't/couldn't find answer to, which is -- how to find the name of the NIM server sitting on the NIM client? All leads to the answer would be much appreciated, many thanks! -- Souvik

LEARN ABOUT SUSE

bootpc

BOOTPC(8)						      Debian GNU/Linux Manual							 BOOTPC(8)

NAME

       bootpc - bootp client

SYNOPSIS

       bootpc  [--bootfile  file]  [--dev  device]  [--verbose]  [--debug] [--server addr] [--hwaddr addr] [--returniffail] [--waitformore length]
       [--in2host addr] [--serverbcast] [--help]

DESCRIPTION

       This manual page documents briefly the bootpc command.  This manual page was written for the Debian GNU/Linux distribution (but may be used
       by others), because the original program does not have a manual page.

       bootpc is a boot protocol client used to grab the machine's IP address, set up DNS nameservers and other useful information.

OPTIONS

       --bootfile file
	      Tell the server to use file as the boot file.

       --dev device
	      Use device to communicate with the server.

       --verbose
	      Be verbose.

       --debug
	      Produce debugging output.

       --server addr
	      Use the IP address addr to communicate with the server.

       --hwaddr addr
	      Use addr as our hardware address rather than what the operating system gives us.

       --returniffail
	      Terminate the program if a failure occurs.  By default bootpc will ask the user to press a key if the request did not succeed.

       --waitformore length
	      Wait for more responses when one is received.  bootpc will wait for at most length seconds.  This is probably only useful for debug-
	      ging.

       --in2host addr
	      Takes an address and returns useful bits of the name after lookup, this was a separate program, but it is more compact to have  both
	      together.

       --serverbcast
	      Tell the server to send back a broadcast reply.  This is necessary on Linux 2.1 and 2.2.

       --help Display the usage of bootpc.

AUTHOR

       This manual page was written by Herbert Xu <herbert@debian.org>, for the Debian GNU/Linux system (but may be used by others).

BOOTPC
								  1999 March 21st							 BOOTPC(8)