07-27-2010
I tried 2 different types of virtual adapters. Same error. The AMD PCI NET and Intel E1000.
It detects both cards just fails to install the adapters.
9 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
I am using SCO Unixware 2.1 & some PC clients are connected, suddenly one message appearslike :
UX:strintercept error: dropping message
this message starts coming repeatedly & agtre some time system hangs.I had to reset the system & now the problem is not there.Please suggest, why this is... (0 Replies)
Discussion started by: paprch
0 Replies
2. AIX
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
Discussion started by: johnf
1 Replies
3. AIX
hello
i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 )
what i need to do after the new adapter installed on the machine?
thanks
best regards
ariec (1 Reply)
Discussion started by: ariec
1 Replies
4. SCO
hi,
anybody can give procedure for how to install oracle 8.0.5 in sco unixware 7.1.4. (0 Replies)
Discussion started by: prakrithi
0 Replies
5. AIX
When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command:
entstat -all ent#|grep -i priority
Priority: 5 Active: False
How to make Active to True? (1 Reply)
Discussion started by: rainbow_bean
1 Replies
6. UNIX for Dummies Questions & Answers
Hi All,
I am new here - this is my first post.
I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Discussion started by: soulmerchant
1 Replies
7. SCO
I am haveing a problem with my VMware ESXi 4.1 server and a virtual SCO UnixWare 7.1.4 server that I need for a legacy application for my company. The problem seems simple but I can't find a solution. The UnixWare (UW) server is a clean install and patched as SCO recommends. I am able to telnet to... (1 Reply)
Discussion started by: DudeCrush
1 Replies
8. SCO
Hello Dears,
I have fujitsu tx300 S7 server with installed sco unixware 7.1.4,
Now the /etc is corrupted and the sco cannot boot.
There is no emergency disk or cd, I'm trying to fix this with reinstalling unixware again, but the problem now that when i try to install the HBA driver that i... (26 Replies)
Discussion started by: amr ibrahim
26 Replies
9. SCO
hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback.
show message :
dlpid:unable to open network adapter driver... (14 Replies)
Discussion started by: moein.mojtaba
14 Replies
ee(7) Miscellaneous Information Manual ee(7)
NAME
ee - Intel (82558/28559) PCI 10/100 Ethernet
SYNOPSIS
config_driver ee
DESCRIPTION
The ee interface supports the Intel 82558 and 82559-based Compaq adapters (including the DE60x line of adapters). These PCI bus adapters
support standard 10/100 Ethernet operation, and provide equivalent service compared to the DE500-BA adapters (IEEE 802.3u Autonegotiation,
full/half duplex, 10/100 Mbps). In addition to the standard features, the Compaq adapters support a hardware feature called parallel
detection. This feature detects speed (10/100) and mode (full/half duplex) automatically when connecting to a repeater/switch that does
NOT perform IEEE 802.3u Autonegotiation.
By default, the driver uses Autonegotiation mode. This mode either connects to the remote partner with IEEE 802.3u Autonegotiation or
resolves the speed and mode using parallel detection. The adapters are designed to automatically connect to all network configurations
without manual intervention. However, if manual intervention is required, lan_config operations are supported (see lan_config(8) for more
information). If you want to preserve your lan_config command information across system restarts, edit the /etc/inet.local file and
include the appropriate commands. This information also remains the same through system version updates.
This driver does NOT require new console firmware to operate in a runtime only manner. Tru64 UNIX does not use console variables to define
media, mode, or speed. Booting over a network requires SRM firmware Version 5.5 or later (on most platforms).
ERRORS
The following diagnostic error messages contain relevant information provided by the ee interface, and are printed on the console. Each
message begins with the adapter identification, including the unit number of the adapter. The ee driver found a system that has not
defined cachelinesize in the PCI configuration header. This is an informational message only, and the driver correctly defines the cache-
linesize parameter. Not enough free memory exists to run the driver. The EEPROM on the board did not pass the checksum test. The board
indicated in this message is unusable. The device did not pass self test. The diagnostic test that failed follows immediately after this
message. The board indicated in this message is unusable.
RELATED INFORMATION
Commands: lan_config(8)
Files: inet.local(4) delim off
ee(7)