07-27-2010
I tried 2 different types of virtual adapters. Same error. The AMD PCI NET and Intel E1000.
It detects both cards just fails to install the adapters.
9 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
I am using SCO Unixware 2.1 & some PC clients are connected, suddenly one message appearslike :
UX:strintercept error: dropping message
this message starts coming repeatedly & agtre some time system hangs.I had to reset the system & now the problem is not there.Please suggest, why this is... (0 Replies)
Discussion started by: paprch
0 Replies
2. AIX
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
Discussion started by: johnf
1 Replies
3. AIX
hello
i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 )
what i need to do after the new adapter installed on the machine?
thanks
best regards
ariec (1 Reply)
Discussion started by: ariec
1 Replies
4. SCO
hi,
anybody can give procedure for how to install oracle 8.0.5 in sco unixware 7.1.4. (0 Replies)
Discussion started by: prakrithi
0 Replies
5. AIX
When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command:
entstat -all ent#|grep -i priority
Priority: 5 Active: False
How to make Active to True? (1 Reply)
Discussion started by: rainbow_bean
1 Replies
6. UNIX for Dummies Questions & Answers
Hi All,
I am new here - this is my first post.
I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Discussion started by: soulmerchant
1 Replies
7. SCO
I am haveing a problem with my VMware ESXi 4.1 server and a virtual SCO UnixWare 7.1.4 server that I need for a legacy application for my company. The problem seems simple but I can't find a solution. The UnixWare (UW) server is a clean install and patched as SCO recommends. I am able to telnet to... (1 Reply)
Discussion started by: DudeCrush
1 Replies
8. SCO
Hello Dears,
I have fujitsu tx300 S7 server with installed sco unixware 7.1.4,
Now the /etc is corrupted and the sco cannot boot.
There is no emergency disk or cd, I'm trying to fix this with reinstalling unixware again, but the problem now that when i try to install the HBA driver that i... (26 Replies)
Discussion started by: amr ibrahim
26 Replies
9. SCO
hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback.
show message :
dlpid:unable to open network adapter driver... (14 Replies)
Discussion started by: moein.mojtaba
14 Replies
DPT(4) BSD Kernel Interfaces Manual DPT(4)
NAME
dpt -- DPT RAID Controller SCSI driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device dpt
For one or more EISA cards:
device eisa
For one or more ISA cards:
device isa
For one or more PCI cards:
device pci
To allow PCI adapters to use memory mapped I/O if enabled:
options DPT_ALLOW_MEMIO
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
dpt_load="YES"
DESCRIPTION
The dpt driver supports DPT RAID SCSI controllers.
SmartRAID (PM3???) are "Enterprise" class cards, and SmartCache (PM2???) cards are in the "Workstation" class. The Gen 4 Smart Cache IV
products were a re-issue of the Gen 3 utilizing upgraded (and cheaper to produce) silicon. The PM3334 (Smart RAID III) was not revamped as
there was no upgraded silicon (68040 processor) and it was using the best DPT made. Note there has been customer confusion over the faster
enterprise class card supported by this driver being an older generation. The Gen5 cards are supported by the asr(4) driver.
HARDWARE
The dpt driver provides support for the following RAID adapters:
o DPT Smart Cache Plus
o Smart Cache II (PM2?2?, PM2022 [EISA], PM2024/PM2124 [PCI]) (Gen2)
o Smart RAID II (PM3?2?, PM3021, PM3222)
o Smart Cache III (PM2?3?)
o Smart RAID III (PM3?3?, PM3332 [EISA], PM3334UW [PCI]) (Gen3)
o Smart Cache IV (PM2?4?, PM2042 [EISA], PM2044/PM2144 [PCI]) (Gen4)
o Smart RAID IV
SEE ALSO
asr(4), cd(4), ch(4), da(4), sa(4), scsi(4)
HISTORY
The dpt driver first appeared in FreeBSD 2.2.6.
AUTHORS
The dpt driver was written by Simon Shapiro and ported to the CAM SCSI system by Justin T. Gibbs.
BSD
June 18, 2006 BSD