07-26-2010
Didn't work.. Same error.
9 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
I am using SCO Unixware 2.1 & some PC clients are connected, suddenly one message appearslike :
UX:strintercept error: dropping message
this message starts coming repeatedly & agtre some time system hangs.I had to reset the system & now the problem is not there.Please suggest, why this is... (0 Replies)
Discussion started by: paprch
0 Replies
2. AIX
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
Discussion started by: johnf
1 Replies
3. AIX
hello
i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 )
what i need to do after the new adapter installed on the machine?
thanks
best regards
ariec (1 Reply)
Discussion started by: ariec
1 Replies
4. SCO
hi,
anybody can give procedure for how to install oracle 8.0.5 in sco unixware 7.1.4. (0 Replies)
Discussion started by: prakrithi
0 Replies
5. AIX
When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command:
entstat -all ent#|grep -i priority
Priority: 5 Active: False
How to make Active to True? (1 Reply)
Discussion started by: rainbow_bean
1 Replies
6. UNIX for Dummies Questions & Answers
Hi All,
I am new here - this is my first post.
I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Discussion started by: soulmerchant
1 Replies
7. SCO
I am haveing a problem with my VMware ESXi 4.1 server and a virtual SCO UnixWare 7.1.4 server that I need for a legacy application for my company. The problem seems simple but I can't find a solution. The UnixWare (UW) server is a clean install and patched as SCO recommends. I am able to telnet to... (1 Reply)
Discussion started by: DudeCrush
1 Replies
8. SCO
Hello Dears,
I have fujitsu tx300 S7 server with installed sco unixware 7.1.4,
Now the /etc is corrupted and the sco cannot boot.
There is no emergency disk or cd, I'm trying to fix this with reinstalling unixware again, but the problem now that when i try to install the HBA driver that i... (26 Replies)
Discussion started by: amr ibrahim
26 Replies
9. SCO
hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback.
show message :
dlpid:unable to open network adapter driver... (14 Replies)
Discussion started by: moein.mojtaba
14 Replies
LEARN ABOUT SUNOS
asadmin-list-resource-adapter-configs
asadmin-list-resource-adapter-configs(1AS) User Commands asadmin-list-resource-adapter-configs(1AS)
NAME
asadmin-list-resource-adapter-configs, list-resource-adapter-configs - lists the configuration information created in domain.xml for the
connector module
SYNOPSIS
list-resource-adapter-configs --user admin_user [--password admin_password][--host localhost] [--port 4848][--secure|-s] [--passwordfile
filename] [--terse=false] [--echo=false] [--interactive=true] [--verbose=false][--ranameconnector_module_name]
Lists the configuration information in the domain.xml for the connector module. It lists an entry called resource-adapter-config in the
domain.xml.
This command is supported in remote mode only.
OPTIONS
--user authorized domain application server administrative username.
--password password to administer the domain application server.
--host machine name where the domain application server is running.
--port port number of the domain application server listening for administration requests.
--secure if true, uses SSL/TLS to communicate with the domain application server.
--passwordfile file containing the domain application server password.
--terse indicates that any output data must be very concise, typically avoiding human-friendly sentences and favoring well-
formatted data for consumption by a script. Default is false.
--echo setting to true will echo the command line statement on the standard output. Default is false.
--interactive if set to true (default), only the required password options are prompted.
--verbose if set to true the properties that are configured are also listed. Default is false.
OPERANDS
raname the value kept in the resource-adapter-name in the domain.xml file.
Example 1: Using list-resource-adapter-configs
asadmin> list-resource-adapter-configs --username admin1
--password adminadmin1
Command list-resource-adapter-configs executed successfully
EXIT STATUS
0 command executed successfully
1 error in executing the command
asadmin-create-resource-adapter-config(1AS), asadmin-delete-resource-adapter-config(1AS)
J2EE 1.4 SDK March 2004 asadmin-list-resource-adapter-configs(1AS)