07-26-2010
Didn't work.. Same error.
9 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
I am using SCO Unixware 2.1 & some PC clients are connected, suddenly one message appearslike :
UX:strintercept error: dropping message
this message starts coming repeatedly & agtre some time system hangs.I had to reset the system & now the problem is not there.Please suggest, why this is... (0 Replies)
Discussion started by: paprch
0 Replies
2. AIX
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
Discussion started by: johnf
1 Replies
3. AIX
hello
i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 )
what i need to do after the new adapter installed on the machine?
thanks
best regards
ariec (1 Reply)
Discussion started by: ariec
1 Replies
4. SCO
hi,
anybody can give procedure for how to install oracle 8.0.5 in sco unixware 7.1.4. (0 Replies)
Discussion started by: prakrithi
0 Replies
5. AIX
When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command:
entstat -all ent#|grep -i priority
Priority: 5 Active: False
How to make Active to True? (1 Reply)
Discussion started by: rainbow_bean
1 Replies
6. UNIX for Dummies Questions & Answers
Hi All,
I am new here - this is my first post.
I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Discussion started by: soulmerchant
1 Replies
7. SCO
I am haveing a problem with my VMware ESXi 4.1 server and a virtual SCO UnixWare 7.1.4 server that I need for a legacy application for my company. The problem seems simple but I can't find a solution. The UnixWare (UW) server is a clean install and patched as SCO recommends. I am able to telnet to... (1 Reply)
Discussion started by: DudeCrush
1 Replies
8. SCO
Hello Dears,
I have fujitsu tx300 S7 server with installed sco unixware 7.1.4,
Now the /etc is corrupted and the sco cannot boot.
There is no emergency disk or cd, I'm trying to fix this with reinstalling unixware again, but the problem now that when i try to install the HBA driver that i... (26 Replies)
Discussion started by: amr ibrahim
26 Replies
9. SCO
hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback.
show message :
dlpid:unable to open network adapter driver... (14 Replies)
Discussion started by: moein.mojtaba
14 Replies
LEARN ABOUT HPUX
xtappaddworkproc
XtAppAddWorkProc() XtAppAddWorkProc()
XtAppAddWorkProc - register a procedure to be called when the event loop is idle.
Synopsis
XtWorkProcId XtAppAddWorkProc(app_context, proc, client_data)
XtAppContext app_context;
XtWorkProc proc;
XtPointer client_data;
Inputs
app_context
Specifies the application context.
proc Specifies the procedure that is to be called when the application is idle.
client_data
Specifies data to be passed to proc when it is called.
Returns
A handle of type XtWorkProcId that can be passed to XtRemoveWorkProc() to unregister the work procedure.
Description
XtAddWorkProc() registers the procedure proc and the data client_data to be called by XtAppNextEvent() or XtAppProcessEvent() when there
are no pending input events and it would otherwise block. Multiple work procedures can be registered, and the most recently added one is
always the one that is called. However, if a work procedure itself adds another work procedure, the newly added one has lower priority
than the current one.
A work procedure returns a Boolean. If it returns True, it will automatically be unregistered and will not be called again. If it returns
False it will be called the next time the application is idle. See XtWorkProc(2) for more information.
Usage
XtAppAddWorkProc() implements a limited form of background processing. Most applications spend most of their time waiting for input; to do
useful work during this idle time, you can register a work procedure that will run when the application is idle.
A work procedure must return quickly or the application will not be able to promptly respond to user events. If a large task needs to be
done in the background, the work procedure should periodically save its state and return False. Work procedures should not be used to do
frivolous work in the background. In a multi-tasking system, an idle application should generally actually be idle, and not steal CPU time
from other processes.
A work procedure can be explicitly removed by calling XtRemoveWorkProc() with the XtWorkProcId returned by this function.
Structures
The XtWorkProcId type is defined as follows:
typedef unsigned long XtWorkProcId;
See Also
XtAppNextEvent(1), XtAppProcessEvent(1), XtRemoveWorkProc(1),
XtWorkProc(2).
Xt - Event Handling XtAppAddWorkProc()