Sponsored Content
Top Forums UNIX for Dummies Questions & Answers SCO Unixware 7.1.4 Network Adapter Error Post 302439962 by flashinwrx on Sunday 25th of July 2010 10:09:47 AM
Old 07-25-2010
Thought I'd just add in here at this point I'm a bit of a dummy when it comes to UNIX..!

How to I reopen for kernel and take settings for eth card module?
 

9 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

SCO Unixware 2.1

I am using SCO Unixware 2.1 & some PC clients are connected, suddenly one message appearslike : UX:strintercept error: dropping message this message starts coming repeatedly & agtre some time system hangs.I had to reset the system & now the problem is not there.Please suggest, why this is... (0 Replies)
Discussion started by: paprch
0 Replies

2. AIX

hacmp network adapter re-define

I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
Discussion started by: johnf
1 Replies

3. AIX

change network adapter

hello i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 ) what i need to do after the new adapter installed on the machine? thanks best regards ariec (1 Reply)
Discussion started by: ariec
1 Replies

4. SCO

sco unixware + oracle 8.0.5

hi, anybody can give procedure for how to install oracle 8.0.5 in sco unixware 7.1.4. (0 Replies)
Discussion started by: prakrithi
0 Replies

5. AIX

How to active this network adapter?

When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command: entstat -all ent#|grep -i priority Priority: 5 Active: False How to make Active to True? (1 Reply)
Discussion started by: rainbow_bean
1 Replies

6. UNIX for Dummies Questions & Answers

External Network Adapter for Solaris 10

Hi All, I am new here - this is my first post. I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Discussion started by: soulmerchant
1 Replies

7. SCO

VMware and SCO Unixware 7.1.4 Network issue

I am haveing a problem with my VMware ESXi 4.1 server and a virtual SCO UnixWare 7.1.4 server that I need for a legacy application for my company. The problem seems simple but I can't find a solution. The UnixWare (UW) server is a clean install and patched as SCO recommends. I am able to telnet to... (1 Reply)
Discussion started by: DudeCrush
1 Replies

8. SCO

Sco UNIXware 7.1.4 error in booting

Hello Dears, I have fujitsu tx300 S7 server with installed sco unixware 7.1.4, Now the /etc is corrupted and the sco cannot boot. There is no emergency disk or cd, I'm trying to fix this with reinstalling unixware again, but the problem now that when i try to install the HBA driver that i... (26 Replies)
Discussion started by: amr ibrahim
26 Replies

9. SCO

Can not recognize network adapter SCO UNIX in HP z400

hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback. show message : dlpid:unable to open network adapter driver... (14 Replies)
Discussion started by: moein.mojtaba
14 Replies
3C589_CS(4)						     Kernel Interfaces Manual						       3C589_CS(4)

NAME
3c589_cs - 3Com 3c589 Etherlink III device driver SYNOPSIS
insmod 3c589_cs.o [pc_debug=n] [if_port=n] [irq_list=i,j,...] DESCRIPTION
3c589_cs is the low-level Card Services driver for the 3Com 3c589 PCMCIA ethernet adapter and 3Com 3c562/3c563 combo cards. When this driver is attached to a card, it allocates the next available ethernet device (eth0..eth#). This device name will be reported in the ker- nel log file, and passed on to cardmgr(8). With the default transceiver setting, the driver will attempt to continuously autodetect the transceiver type (10base2 or 10baseT). There should normally only be a one or two second lag before the correct transceiver is selected. On particularly noisy or busy networks, it is possible for the detection logic to incorrectly toggle the transceiver type. If this becomes a problem, it may be necessary to explicitly select the interface type when the module is loaded or with the ifport command. PARAMETERS
pc_debug=n Selects the PCMCIA debugging level. This parameter is only available if the module is compiled with debugging enabled. A non-zero value enables debugging. if_port=n Selects the transceiver type. 0 is autodetect (10baseT or 10base2), 1 is 10baseT (twisted pair), 2 is 10base2 (BNC, or thin net). and 3 is AUI (thick ethernet). The default is 0 (autodetect). irq_list=i,j,... Specifies the set of interrupts that may be allocated by this driver. DIAGNOSTICS
eth#: interrupt(s) dropped! Indicates that the driver did not receive an interrupt notification for some reason. The driver will poll the card (with a signifi- cant performance penalty) if the problem persists. The most likely cause is an interrupt conflict and/or host bridge configuration problem. AUTHOR
David Hinds - dahinds@users.sourceforge.net SEE ALSO
cardmgr(8), pcmcia(5), ifport(8). pcmcia-cs 2000/06/12 21:24:48 3C589_CS(4)
All times are GMT -4. The time now is 03:50 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy