I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached.
I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network Config Manager but has the same error.
I've tried updating with MP5 with latest drivers but does not seem to work. I've also used the "# pkgadd -d diskette1" command but it fails half way through for some unknown reason.
I am using SCO Unixware 2.1 & some PC clients are connected, suddenly one message appearslike :
UX:strintercept error: dropping message
this message starts coming repeatedly & agtre some time system hangs.I had to reset the system & now the problem is not there.Please suggest, why this is... (0 Replies)
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
hello
i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 )
what i need to do after the new adapter installed on the machine?
thanks
best regards
ariec (1 Reply)
When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command:
entstat -all ent#|grep -i priority
Priority: 5 Active: False
How to make Active to True? (1 Reply)
Hi All,
I am new here - this is my first post.
I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
I am haveing a problem with my VMware ESXi 4.1 server and a virtual SCO UnixWare 7.1.4 server that I need for a legacy application for my company. The problem seems simple but I can't find a solution. The UnixWare (UW) server is a clean install and patched as SCO recommends. I am able to telnet to... (1 Reply)
Hello Dears,
I have fujitsu tx300 S7 server with installed sco unixware 7.1.4,
Now the /etc is corrupted and the sco cannot boot.
There is no emergency disk or cd, I'm trying to fix this with reinstalling unixware again, but the problem now that when i try to install the HBA driver that i... (26 Replies)
hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback.
show message :
dlpid:unable to open network adapter driver... (14 Replies)
Discussion started by: moein.mojtaba
14 Replies
LEARN ABOUT DEBIAN
fastx_clipper
FASTX_CLIPPER(1) User Commands FASTX_CLIPPER(1)NAME
fastx_clipper - FASTA/Q Clipper
DESCRIPTION
usage: fastx_clipper [-h] [-a ADAPTER] [-D] [-l N] [-n] [-d N] [-c] [-C] [-o] [-v] [-z] [-i INFILE] [-o OUTFILE] Part of FASTX Toolkit
0.0.13.2 by A. Gordon (gordon@cshl.edu)
[-h] = This helpful help screen.
[-a ADAPTER] = ADAPTER string. default is CCTTAAGG (dummy adapter). [-l N] = discard sequences shorter than N nucleotides.
default is 5. [-d N] = Keep the adapter and N bases after it.
(using '-d 0' is the same as not using '-d' at all. which is the default).
[-c] = Discard non-clipped sequences (i.e. - keep only sequences which contained the adapter).
[-C] = Discard clipped sequences (i.e. - keep only sequences which did not contained the adapter).
[-k] = Report Adapter-Only sequences.
[-n] = keep sequences with unknown (N) nucleotides. default is to discard such sequences.
[-v] = Verbose - report number of sequences.
If [-o] is specified,
report will be printed to STDOUT.
If [-o] is not specified (and output goes to STDOUT), report will be printed to STDERR.
[-z] = Compress output with GZIP.
[-D] = DEBUG output.
[-M N] = require minimum adapter alignment length of N.
If less than N nucleotides aligned with the adapter - don't clip it.
[-i INFILE] = FASTA/Q input file. default is STDIN.
[-o OUTFILE] = FASTA/Q output file. default is STDOUT.
SEE ALSO
The quality of this automatically generated manpage might be insufficient. It is suggested to visit
http://hannonlab.cshl.edu/fastx_toolkit/commandline.html
to get a better layout as well as an overview about connected FASTX tools.
fastx_clipper 0.0.13.2 May 2012 FASTX_CLIPPER(1)