I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached.
I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network Config Manager but has the same error.
I've tried updating with MP5 with latest drivers but does not seem to work. I've also used the "# pkgadd -d diskette1" command but it fails half way through for some unknown reason.
I am using SCO Unixware 2.1 & some PC clients are connected, suddenly one message appearslike :
UX:strintercept error: dropping message
this message starts coming repeatedly & agtre some time system hangs.I had to reset the system & now the problem is not there.Please suggest, why this is... (0 Replies)
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
hello
i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 )
what i need to do after the new adapter installed on the machine?
thanks
best regards
ariec (1 Reply)
When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command:
entstat -all ent#|grep -i priority
Priority: 5 Active: False
How to make Active to True? (1 Reply)
Hi All,
I am new here - this is my first post.
I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
I am haveing a problem with my VMware ESXi 4.1 server and a virtual SCO UnixWare 7.1.4 server that I need for a legacy application for my company. The problem seems simple but I can't find a solution. The UnixWare (UW) server is a clean install and patched as SCO recommends. I am able to telnet to... (1 Reply)
Hello Dears,
I have fujitsu tx300 S7 server with installed sco unixware 7.1.4,
Now the /etc is corrupted and the sco cannot boot.
There is no emergency disk or cd, I'm trying to fix this with reinstalling unixware again, but the problem now that when i try to install the HBA driver that i... (26 Replies)
hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback.
show message :
dlpid:unable to open network adapter driver... (14 Replies)
Discussion started by: moein.mojtaba
14 Replies
LEARN ABOUT CENTOS
iprupdate
IPRUPDATE(8) System Manager's Manual IPRUPDATE(8)NAME
iprupdate - IBM Power RAID adapter/device microcode update utility
SYNOPSIS
iprupdate
iprupdate --debug --check_only --daemon --use-polling --use-uevents
DESCRIPTION
iprupdate is used to update the microcode on IBM storage adapters and the disk units attached to them to a minimum supported level. It can
be run at any time while the ipr device driver is loaded. The utility will check the microcode revision level of each storage adapter/disk
unit on the system and compare it to the microcode revision level that is installed in /etc/microcode, /usr/lib/microcode, and
/lib/firmware. If the microcode level on the adapter/device is below the minimum supported level and the level of the latest image is
newer, the microcode will be updated to the latest level available. It is desired that this be called in the boot process.
OPTIONS --version
Print the version number of iprupdate
--debug
Enable additional error logging. Enabling this will result in additional errors logging to /var/log/messages.
--check_only
Check if any adapters or disk units are below their minimum supported level.
--daemon
Run as a daemon to handle adapters and devices being hotplugged.
--use-polling
Do not use netlink/uevent notification, but rather poll for adapter and device configuration changes.
--use-uevents
Use netlink/uevent notification rather than polling for adapter and device configuration changes. If not specified, polling will be
used until the first uevent notification appears, then netlink will be used.
AUTHOR
Brian King (brking@us.ibm.com)
February 2005 IPRUPDATE(8)