Sponsored Content
Special Forums IP Networking FTP failure due to network problem Post 302438199 by vibora on Monday 19th of July 2010 05:13:55 AM
Old 07-19-2010
FTP failure due to network problem

Hi,

I've been searching through out this forum to find the exact message when during the on-going FTP, suddenly the network went down but i cannot find some. Could anyone provide me the exact return codes when FTP failed during FTP or prior to FTP the network went down and you still proceeded to FTP.

Below is the sample of a "successfull" FTP. I think the message after "Connection will close if idle more than 5 minutes." is what i need.

Code:
220-QTCP at test07.
220 Connection will close if idle more than 5 minutes.
331 Enter password.
230 PULSE logged on.
250  Now using naming format "1".
200 Representation type is binary IMAGE.
?Invalid command
?Invalid command
200 PORT subcommand request successful.
150 Retrieving file /xx/yyy/zzz/aaa/S0715-10
250 File transfer completed successfully.
2021 bytes received in 0.02369 seconds (83.29 Kbytes/s)
local: /home/xxx/S0715-10.txt remote: /xx/yyy/zzz/aaa/S0715-10.
txt
221 QUIT subcommand received.

Thanks

Last edited by vibora; 07-19-2010 at 06:26 AM..
 

10 More Discussions You Might Find Interesting

1. Shell Programming and Scripting

Determining the failure or success of FTP

Hi there, I am in the process of writing a shell script to transfer files to a remote directory. Is there a method to determine the success or the failure of the ftp process. Regards Jim (4 Replies)
Discussion started by: JimJim
4 Replies

2. UNIX for Dummies Questions & Answers

failure writing network systems-ftp error

Hi, I tried to do a ftp get process from linux server to a remote system.It was giving an error 'failure writing network systems'.I am trying to ftp two files,one among them is successful and this problem occurs only if i run the code through 'cron' ie,manual run ends successfully. Would... (0 Replies)
Discussion started by: DILEEP410
0 Replies

3. Filesystems, Disks and Memory

ACL problem due to mv command used in solaris

Hi All, Is there any way to use mv command and that should apply ACL on the moved files that is already set in distination location This mv command is running in a solaris system. File system is NFS. Problem I am facing : Currently mv command removes ACL from moved files and also it... (0 Replies)
Discussion started by: Tlogine
0 Replies

4. Shell Programming and Scripting

Script problem due to recursive directories Help please

Hello everyone , I am looking for a better solution then the one I have created for the my Task The task is: Create an automated script that will check for Uploads in a specified Directory and move them to another specified Directory if the files are completely uploaded. Files are FTP'd to... (2 Replies)
Discussion started by: robertmcol
2 Replies

5. UNIX for Advanced & Expert Users

Problem due to Fork Error

Hi, I have developed a datastage job...which has many process running in parallel..but because of Fork Error my job is not working:( Can any body help me out to solve this Fork error problem.:rolleyes: My Os is SUNOS. IS there any setting in Unix through admin where in if i set some paramter... (8 Replies)
Discussion started by: Amey Joshi
8 Replies

6. Shell Programming and Scripting

Retry upon FTP failure

I am using the following code in a C Shell script to transfer files to a remote server: ftp -n logxx.xxxx.xxx.xxx.com <<DO_FTP1 quote user $user_name quote pass $password ascii put $js_file_name bin put $FinalZipFile quit DO_FTP1 This code works great except on those rare occasions... (8 Replies)
Discussion started by: phudgens
8 Replies

7. Shell Programming and Scripting

FTP failure with different scenario

Hi Gurus the below FTP code works fine, but the issue is from past 1 week couldn't able to send the files to external system. #--------------------------------------------------------------------# #Start the ftp session #--------------------------------------------------------------------#... (3 Replies)
Discussion started by: SeenuGuddu
3 Replies

8. Red Hat

Problem in RedHat Cluster Node while network Failure or in Hang mode

Hi, We are having many RedHat linux Server with Cluster facility for availability of service like HTTPD / MySQL. We face some issue while some issue related to power disturbance / fluctuation or Network failure. There is two Cluster Node configured in... (0 Replies)
Discussion started by: hirenkmistry
0 Replies

9. Ubuntu

What is solution for this error "tar: Exiting with failure status due to previous errors"?

Does anyone know what is solution for this error ?tar: Exiting with failure status due to previous errors from last 3 days I am trying to take backup of home/user directory getting again and again same error please anyone give me solution (8 Replies)
Discussion started by: Akshay Hegde
8 Replies

10. UNIX for Advanced & Expert Users

FTP failure

Hi, We have a external vendor (outside firewall), who used to connect our ftp server till 2 days back. I am not able to figure out, what was changed. Now he is not able to login. When I login to ftp server (from inside firewall), I am able to connect with credentials. When that vendor login... (4 Replies)
Discussion started by: solaris_1977
4 Replies
ftpshut(1M)						  System Administration Commands					       ftpshut(1M)

NAME
ftpshut - close down the FTP Servers at a given time SYNOPSIS
ftpshut [-V] [-v] [-l min] [-d min] time [warning-message...] DESCRIPTION
The ftpshut command provides an automated shutdown procedure that the superuser can use to notify FTP users when the FTP Server is shutting down. Ten minutes before shutdown, or immediately if the value of time is less than ten minutes, any new FTP Server connections will be disabled. You may adjust the shutdown of new FTP Server connections by means of the -l option. Five minutes before shutdown, or immediately if the value of time is less than five minutes, all current FTP connections will be discon- nected. You may adjust the shutdown of current FTP connections by means of the -d option. The ftpshut command creates shutdown message files that the FTP Server uses to determine when to shutdown. Separate shutdown message files are created in the anonymous and virtual host FTP Server areas, in addition to the system wide shutdown message file. Once the shutdown occurs, the server continues to refuse connections until the appropriate shutdown message file is removed. This normally is done by using the ftprestart(1M) command. The location of the shutdown message file is specified by the shutdown capability in the ftpaccess file. The following magic cookies are available: %s The time system is going to shut down. %r The time new connections will be denied. %d The time current connections will be dropped. %C The current working directory. %E The maintainer's email address as defined in the ftpaccess file. %F The free space in the partition of CWD, in kilobytes. %L The local host name. %M The maximum allowed number of users in this class. %N The current number of users in this class. %R The remote host name. %T The local time (form Thu Nov 15 17:12:42 1990). %U The username given at login time. OPTIONS
The ftpshut command supports the following options: -V Display program copyright and version information, then terminate. -d min The time ahead of shutdown, in minutes, that existing connections will be disconnected upon completion of their current or next (if idle) FTP request. -l min The time ahead of shutdown, in minutes, that new connections will be refused. -v Verbose. Output the pathname of the shutdown message files created. OPERANDS
The ftpshut command supports the following operands: time The time at which ftpshut will bring the FTP Servers down. time can have a value of now, which indicates an immedi- ate shutdown. Alternatively, time can specify a future time in one of two formats: +number or HHMM. The first form brings the FTP Server down in number minutes. The second brings the FTP Server down at the time of day indicated, using a 24-hour clock format. When using the absolute time format, you can only specify times between now and 23:59. warning-message The message to display that warns of the imminent shutdown. The warning-message will be formatted at 70 characters wide. ftpshut knows the actual string length of the magic cookies. If no warning-message is supplied, the default message "System shutdown at %s" is used. EXIT STATUS
The following exit values are returned: 0 Successful completion. >0 An error occurred. FILES
/etc/ftpd/ftpaccess /etc/ftpd/ftpservers ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWftpu | +-----------------------------+-----------------------------+ |Interface Stability |External | +-----------------------------+-----------------------------+ SEE ALSO
in.ftpd(1M), ftprestart(1M), shutdown(1M), ftpaccess(4), ftpservers(4), attributes(5) SunOS 5.10 1 May 2003 ftpshut(1M)
All times are GMT -4. The time now is 04:48 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy