07-15-2010
1. Boot from CD
2. Start network services
3. access remote drive or use NFS to restore
9 More Discussions You Might Find Interesting
1. Solaris
Setting up a T5240 with two disks c1t0d0 and c1t1d0.
I am trying to use raidctl but when I issue.
raidctl -l
I get
Controller 1
Disk: 0.0.0
Disk: 0.1.0
So I try
raidctl -c '0.0.0 0.1.0' -r 1 1
and I get "Array in use."
I try (4 Replies)
Discussion started by: photon
4 Replies
2. Solaris
its a fresh installation. during the OS setup, it did not prompt for IP, netmask and gateway. using Solaris 10 08/07 update 4. I tried to plumb manually but encountered no such interface error. but nxge interfaces can be greped from the /etc/path_to_inst file.
getting similar error on... (3 Replies)
Discussion started by: incredible
3 Replies
3. Solaris
I was trying to configure the netmgmt from the serial and set commitpending to true. However, the netmgmt port is not up and blinking.
I tried to connect using my notebook directly to the netmgmt port and am not able to ping as well. Previouly i was doing the firmware upgrade using the webconsole.... (20 Replies)
Discussion started by: incredible
20 Replies
4. Solaris
Hi,
We are planning to buy new server for our data center. Sun T5240 or M3000 which one have better performance, we are going to create many dt sessions in this server. So, i need your suggestions.
RJS (4 Replies)
Discussion started by: rajasekg
4 Replies
5. Solaris
Hi -
I have a T5240 with 7 LDOMS configured. One night, network comm was broken somehow. Nobody was doing anything on the machine at the time. Here is what I saw in messages:
WARNING: nxge3 : nxge_dma_mem_alloc: ddi_dma_mem_alloc kmem alloc failed
WARNING: nxge3 : nxge_alloc_rx_buf_dma:... (2 Replies)
Discussion started by: pyroman
2 Replies
6. Solaris
Hi Gurus
Can any one tell me the process of disabling the multithreading option on T5240 server and my OS is on LDOM, having one physical processor with 8 core & 8 thread per core
Regards (3 Replies)
Discussion started by: amity
3 Replies
7. Solaris
Hi !
I've been given a T5240 with 4 disks and 2 HBA cards (but no array connected). I did a factory reset on SP and NVRAM clean on OBP because the server had been used before.
I boot cdrom in single mode and try to create a hw mirror with disks from c1... but only c2 is seen by raidctl.
... (2 Replies)
Discussion started by: delavega
2 Replies
8. Solaris
I have a T5240 with 2 T2 US 8 core.. Theoretically how many ldoms can I configure? (5 Replies)
Discussion started by: Iftikhar Barrie
5 Replies
9. Solaris
Hi Folks,
Just a quick question - hopefully!
I have an application currently running on a V890 with Solaris 9, I'd like to move this to either one of our T-5's or one of the T5240's in a Legacy container on an LDOM - but the fly in the ointment is the application still uses a standard Hayes... (3 Replies)
Discussion started by: gull04
3 Replies
LEARN ABOUT DEBIAN
tapset::scsi
TAPSET::SCSI(3stap) TAPSET::SCSI(3stap)
NAME
tapset::scsi - systemtap scsi probe points
DESCRIPTION
This family of probe points is used to probe the SCSI activities. It contains the following probe points:
scsi.ioentry
Fires when SCSI mid layer prepares a SCSI request
Arguments:
disk_major
The major number of the disk
disk_minor
The minor number of the disk
device_state
The current state of the device. The possible values could be:
SDEV_CREATED = 1, /* device created but not added to sysfs
* Only internal commands allowed (for inq) */
SDEV_RUNNING = 2, /* device properly configured
* All commands allowed */
SDEV_CANCEL = 3, /* beginning to delete device
* Only error handler commands allowed */
SDEV_DEL = 4, /* device deleted
* no commands allowed */
SDEV_QUIESCE = 5, /* Device quiescent. No block commands
* will be accepted, only specials (which
* originate in the mid-layer) */
SDEV_OFFLINE = 6, /* Device offlined (by error handling or
* user request */
SDEV_BLOCK = 7, /* Device blocked by scsi lld. No scsi
* commands from user or midlayer should be issued
* to the scsi lld. */
scsi.iodispatching
Fires when the SCSI mid layer dispatches a SCSI command to the low level driver
Arguments:
host_no
The host number
channel
The channel number
lun
The lun number
dev_id
The scsi device id
device_state
The current state of the device.
data_direction
The data_direction specifies whether this command is from/to the device.
The possible values could be:
DMA_BIDIRECTIONAL = 0,
DMA_TO_DEVICE = 1,
DMA_FROM_DEVICE = 2,
DMA_NONE = 3,
request_buffer
The request buffer address
req_bufflen
The request buffer length
scsi.iodone
Fires when a SCSI command is done by low level driver and enqueued into the done queue.
Arguments:
host_no
The host number
channel
The channel number
lun
The lun number
dev_id
The scsi device id
device_state
The current state of the device
data_direction
The data_direction specifies whether this command is from/to the device.
scsi.iocompleted
Fires when SCSI mid layer runs the completion processing for block device I/O requests
Arguments:
host_no
The host number
channel
The channel number
lun
The lun number
dev_id
The scsi device id
device_state
The current state of the device
data_direction
The data_direction specifies whether this command is from/to the device.
goodbytes
The bytes completed.
SEE ALSO
stap(1), stapprobes(3stap)
IBM
TAPSET::SCSI(3stap)