I am trying to add a route for assign a network interface to the traffic to/from a specific net, but allways to get the same system message : network is unreacheable
Code:
root@ColectorDMSCNT # route add net 200.44.46.0/24 161.196.84.196 1
add net 200.44.46.0/24: gateway 161.196.84.196: Network is unreachable
root@ColectorDMSCNT # ping 161.196.84.196
161.196.84.196 is alive
root@ColectorDMSCNT # traceroute 161.196.84.196
traceroute: Warning: Multiple interfaces found; using 161.196.84.196 @ e1000g1
traceroute to 161.196.84.196 (161.196.84.196), 30 hops max, 40 byte packets
1 Monitoreo (161.196.84.196) 0.286 ms 0.109 ms 0.106 ms
root@ColectorDMSCNT # ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
e1000g0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 10.119.64.6 netmask ffffff00 broadcast 10.119.64.255
ether 0:14:4f:e4:3:18
e1000g1: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 3
inet 161.196.84.196 netmask ffffffc0 broadcast 161.196.84.255
ether 0:14:4f:e4:3:19
I am running RH7.3 on a compaq presario box. The network card is a Linksys one. I am only able to communicate with the local network (only the local IPs are accessible). When I try to ping another box I get a "Connect: Network is unreachable" message. What could be the problem.
Thanks in... (2 Replies)
Hi,
I am trying to add route command in Solaris 10 machine in the following fashion:
route add -host 10.8.112.10 180.144.1.250 -interface lo0:1
this command fails with an error "lo0:1: bad value"
I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
hi,
i would like to share this
/etc/sysconfig/network-script/route-eth0
GATEWAY0=XXXXXX
NETMASK0=XXXXXX
ADDRESS0=XXXXXXX
a delete route command with "route del -net xxxx...." will work but if the above exist and you reboot the linux then old route will be invoke on that config-route.
... (0 Replies)
Hi All,
yesterday I was trying to add a network route to my solaris 8 host using 'route add'. Everytime I tried, I kept getting the response 'network is unreachable'.
I was trying all kinds of different methods, however I eventually got it to work after bouncing the interface that I was... (2 Replies)
Hi there,
I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far:
# route add... (2 Replies)
I have built a new linux server, via a iLo connection.
and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty.
Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the... (0 Replies)
Please , I have a problem
I have add a statis route on Solaris 10, but after this, the network interface of Server was Offline.
The system is in cluster mode (3.2)
route add -net 10.10.1.128 -netmask 255.255.255.128 10.10.1.51
-------------------
lo0:... (1 Reply)
Assalam o Alaikum!
After configuring and starting service of samba, when I access shared folder from windows XP it gives this error " Network Route was not found".
My server IP 192.168.1.252, client is on same network.
selinux is disabled
smb,conf:
workgroup = WORKGROUP
server string =... (2 Replies)
Hi,
I have installed RHEL4 using vmware workstation..
Host OS: Windows XP
Guest OS: RHEL4
Pls refer step 17 & 18 in below link...
ORACLE-BASE - Red Hat Enterprise Linux 4 and Centos 4 Installation
1) If i choose to assign IP automatically (using DHCP) means, i am able to connect RHEL4... (3 Replies)
Seems to wanboot ok but then fails to connect to server. What do I need to check?
{0} ok boot net - install
Boot device: /pci@300/pci@1/pci@0/pci@1/network@0 File and args: - install
1G link up
<time unavailable> wanboot info: WAN boot messages->console
<time unavailable>... (2 Replies)
Discussion started by: psychocandy
2 Replies
LEARN ABOUT OSF1
routes
routes(4) Kernel Interfaces Manual routes(4)NAME
routes - Specifies Internet routing information to the routing tables
SYNOPSIS
/etc/routes
DESCRIPTION
Static routes can be defined in the /etc/routes file. The /etc/routes file identifies static routes that are automatically added to the
network routing tables with the /usr/sbin/route add command. The /sbin/init.d/route script contains the /usr/sbin/route add command that
is executed for each entry in the /etc/routes file when the network is restarted on the system or the system is rebooted.
The general format of an entry in the /etc/routes file is: Dest Name1 Name2
The following is a brief description of each element in an /etc/routes file entry: A keyword that indicates whether the route is to a net-
work or to a host. The two possible keywords are -net and -host. The name or address of the destination network or host. Name1 can be
either a symbolic name (as used in the /etc/hosts or /etc/networks file) or an Internet address specified in dotted-decimal format. The
name or address of the gateway host to which messages should be forwarded. Name2 can be either a symbolic name (as used in the /etc/hosts
file) or an Internet address specified in dotted-decimal format.
The routes file is a Context-Dependent Symbolic Link (CDSL) and must be maintained as such. See the System Administration manual for more
information.
EXAMPLES
To specify a route to a network through a gateway host with an entry in the /etc/routes file, enter:
-net net2 host4
This example specifies a route to a network, net2, through the gateway host4. To specify a route to a host through a gateway host
with an entry in the /etc/routes file, enter:
-host host2 host4
This example specifies a route to a host, host2, through the gateway host4. To specify a route to a default gateway host with an
entry in the /etc/routes file, enter:
default 130.9.0.5
This example specifies a route to a default gateway with an Internet address of 130.9.0.5.
FILES
Contains the /usr/sbin/routed add command.
RELATED INFORMATION
Commands: route(8)
Daemons: gated(8), routed(8)
Files: gated.conf(4)
Network Administration delim off
routes(4)
07-08-2010
