i have 2 files
file 1---------> hello
file 2---------> hello world
is there any command that we find the diff b/w two files and gives the ans as what is not matched with file 2.
diff file 1 file 2
here the desired o/p should be: world
as "world" is not found in file 1. (2 Replies)
I know the basic difference between .pm and .pl files. But wat puzzles me is when to go for creating a module and when to create .pl files.Based on wat criteria we sholud decide to make a function whcih implements a common functionality as module or a .pl file ?? (3 Replies)
Hi All,
I need your help to find out the difference between 3 files.
How can i get the output which says that FILE2 contains additional (YYY,900,100) compare to FILE1 and FILE3 contains addition record (ZZZ,904,908) compare to FILE1?
I have tried using diff3 command, but was not able to get... (2 Replies)
I have two files like follows: -
File 1: -
A 20
B 15
D 10
C 6
File 2: -
B 21
A 20
C 11
D 10
Now I want file like this: -
It should pick up 'A' from File 1 and pick up 'A' from File 2 and should get difference of the numbers in 2nd column and display result as follows ... (2 Replies)
HI Folks,
sorry if it is a naive question.
i have two files . "file1.txt" & "file2.txt"
contents in files:
file1.txt file2.txt
-------- ---------
1 ... (2 Replies)
I need the get the difference between 2 files and the result, I need to output it to an other file
file1
1
1
2
file2
1
1
2
3
Result....File3=3
used diff file1 file2 > file3 ( not working as expected)..Exact requirement..I have 2 flatfiles to compare and load only the difference in a... (0 Replies)
Hi all,
I have problem in finding the difference. suppose i have two file
file1 file2
1xyz 1xyz
1asd 1xyz
1asd 1abc
2adf 1asd
3asd 2abd
4abc 2adf
3asf
I need to... (7 Replies)
I have two file as given below which shows the ACL permissions of each file. I need to compare the source file with target file and list down the difference as specified below in required output. Can someone help me on this ?
Source File
*************
# file: /local/test_1
# owner: own
#... (4 Replies)
Discussion started by: sarathy_a35
4 Replies
LEARN ABOUT MINIX
pnmpsnr
pnmpsnr(1) General Commands Manual pnmpsnr(1)NAME
pnmpsnr - compute the difference between two portable anymaps
SYNOPSIS
pnmpsnr [pnmfile1] [pnmfile2]
DESCRIPTION
Reads two PBM, PGM, or PPM files, or PAM equivalents, as input. Prints the peak signal-to-noise ratio (PSNR) difference between the two
images. This metric is typically used in image compression papers to rate the distortion between original and decoded image.
If the inputs are PBM or PGM, pnmpsnr prints the PSNR of the luminance only. Otherwise, it prints the separate PSNRs of the luminance, and
chrominance (Cb and Cr) components of the colors.
The PSNR of a given component is the ratio of the mean square difference of the component for the two images to the maximum mean square
difference that can exist betwee any two images. It is expressed as a decibel value.
The mean square difference of a component for two images is the mean square difference of the component value, comparing each pixel with
the pixel in the same position of the other image. For the purposes of this computation, components are normalized to the scale [0..1].
The maximum mean square difference is identically 1.
So the higher the PSNR, the closer the images are. A luminance PSNR of 20 means the mean square difference of the luminances of the pixels
is 100 times less than the maximum possible difference, i.e. 0.01.
SEE ALSO pnm(5)
04 March 2001 pnmpsnr(1)