Linksys RV802 VPN Router Post: 302433899

9 More Discussions You Might Find Interesting

1. Solaris

I can't ping my linksys router from Ultra 10

To begin with, I am a Solaris newbie; however, I am very familiar with Linux. Until I began working with Solaris, I didn't realize how much more difficult networking Solaris is than Linux. Before submitting this question, I have tried to fix this problem myself. After days of research, I still...

2. IP Networking

router Linksys

I have a linksys router BEFSR41. I am trying to connect two network.. one device has to route from one network of IP address 192.168.10.12 to go to a device on separate network with IP address 192.168.25.95. In the configuration LAN ip address by default it 192.168.1.1 If I define LAN IP to...

3. IP Networking

Connecting SGI to Linksys router

I have an SGI running Irix 6.5 and I am trying to connect it to my home network that consists of two Windows PC's (Win 98SE and Win 2000) plus the SGI all connected to a Linksys router which is connected to my DSL modem. My ISP is Verizon DSL (Dynamic IP addressing.) All network lights are...

4. IP Networking

Setup Dial In VPN on Cisco Router

Hello, Does anyone know where I can find configuration information on setting up a dial in VPN on Cicso IOS for a bunch of servers. Could not seem to find anything in search engines. Thanks

5. IP Networking

linksys router and solaris 8

I just sys-unconfigged my ultra sparc which is on my home network where I have 2 PCs attached. When I go to install Solaris 8, it asks various things re: networking. Specifically, when it asks for the IP addy for the DNS server, I input the info, but it barfs back "IP addy info not found". I...

6. Shell Programming and Scripting

using wget to submit a form on linksys router

I'm trying to use wget to submit a form. I have tried to dig out what is actually being "posted" and where, using tamperdata (see below). http://ubuntuforums.org/attachment.php?attachmentid=109123&d=1239224127 Here is my wget command: wget --http-user=xyz --http-password=xyz...

7. UNIX for Dummies Questions & Answers

Remote Unix printing to my WinXP works with no router. How can I make it work through my router?

I set up remote printing on a clients Unix server to my Windows XP USB printer. My USB printer is connected directly to my PC (no print server and no network input on printer). With my Win XP PC connected to my cable modem (without the router), i can do lp -dhp842c /etc/hosts and it prints. I...

8. Cybersecurity

Linksys router question

Hi I have very basic network settings in my home. Cable connected to my Linksys Wireless G router. My wife and I connect to that using our laptop. Yes. I did enable encryption to connect. Also my wireless printer is connected to that. For some reason, last night around 12:30 AM, the...

9. UNIX for Dummies Questions & Answers

[Solved] Can't get on internet with Linux Static IP address and Linksys Router.

I configured my linux server with Static IP address out of the range of the DHCP linksys router, but cannot get on the internet. When I switch back to "Automatically obtain IP address" ..then I can get on the internet. Can comeone help with this.

LEARN ABOUT DEBIAN

mrtg-ping-probe

MRTG-PING-PROBE(1)					      General Commands Manual						MRTG-PING-PROBE(1)

NAME

       mrtg-ping-probe - ping probe module for Multi Router Traffic Grapher

DESCRIPTION

       mrtg-ping-probe is a ping probe module for MRTG 2.x.  It is used to monitor the round trip time and packet loss to networked devices.  MRTG
       uses the output of mrtg-ping-probe to generate graphs visualizing minimum and maximum round trip times or packet loss.

       mrtg-ping-probe is not run directly, but is called by MRTG as a helper when it needs to determine ping time to a host.

       Act responsibly: do not use mrtg-ping-probe to ping devices without the owner's permission.  Just imagine if 10,000 people decided to  ping
       your hosts!  mrtg-ping-probe is meant to be used within your network to get round trip time performance figures for your network.

OPTIONS

       To  use	mrtg-ping-probe you need to configure MRTG to call it from within the definition of a target host. This is done in the MRTG config
       file, which is usually /etc/mrtg.conf.

       Here's an example snippet: change the target name and IP address to suit your needs.

       Target[your.target.ping]: `/usr/bin/mrtg-ping-probe 123.456.789.123`
       SetEnv[your.target.ping]: MRTG_INT_IP="123.456.789.123" MRTG_INT_DESCR="ping"
       MaxBytes[your.target.ping]: 100
       AbsMax[your.target.ping]: 200
       Options[your.target.ping]: gauge, growright
       YLegend[your.target.ping]: ping time (ms)
       ShortLegend[your.target.ping]: ms
       Legend1[your.target.ping]: Maximum Round Trip Time in ms
       Legend2[your.target.ping]: Minimum Round Trip Time in ms
       Legend3[your.target.ping]: Maximal 5 Minute Maximum Round Trip Time in ms
       Legend4[your.target.ping]: Maximal 5 Minute Minimum Round Trip Time in ms
       LegendI[your.target.ping]: &nbsp;Max:
       LegendO[your.target.ping]: &nbsp;Min:

       Pay close attention to the backticks in the first line which tell MRTG to execute the nominated external program. Note also that  you  need
       to use the "gauge" option, since the results of subsequent ping probes are independant values and not an incrementing counter.

SEE ALSO

       mrtg(1).

       The latest release of mrtg-ping-probe can be found on the web at http://pwo.de/projects/mrtg/

AUTHOR

       This manual page was written by Jonathan Oxer <jon@debian.org>, for the Debian project (but may be used by others).

								  April 14, 2003						MRTG-PING-PROBE(1)