Sponsored Content
Operating Systems HP-UX how can i know this processor quad or dual core ? Post 302433789 by maxim42 on Wednesday 30th of June 2010 01:46:47 PM
Old 06-30-2010
how can i know this processor quad or dual core ?

hi every body
i want to know if i have server with hp-ux os if i did "machinfo" i will see no of cpu = for example 16
how can i know this is dual or quad core .


thanks
 

8 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Problem with dual processor system

Firstly, here are the main system specs: 2x Pentium III 800MHz MSI 694D Pro 4x 256MB PC133 SDRAM 420WATT Vantec PSU In a nut shell, the systems reboots for no apparent reason while starting/installing up any OS when both processors are installed. I've ran memtest86 for several hours, no... (1 Reply)
Discussion started by: meeps
1 Replies

2. Linux

linux for dual core processor

hi all I bought a new MSI motherboard and intel dual core processor . i have currently installed fedora core 3 for which audio is not detected . can u tell me which version of fedora core will support as i have tried with fedora core 6 which gets installed but gives a error while... (0 Replies)
Discussion started by: nageshrk
0 Replies

3. UNIX for Dummies Questions & Answers

difference between Dual-core & Core-to-duo

Can anybody tell What is the exact difference between a Dual-core processor and a Core-to-duo processor ?Advance thanks to all my friends. (1 Reply)
Discussion started by: Ajith kumar.G
1 Replies

4. Red Hat

finding no of core in processor

Hi, what is command to find out no of core per procssor? Regards, Manoj (4 Replies)
Discussion started by: manoj.solaris
4 Replies

5. AIX

Processor and processor core

Guys... Hows it going??? I have been going through the hardware spec of IBM system p systems.. and here i am confused for IBM Power 520 Express it says Processor cores: One, two or four 64-bit 4.2 GHz POWER6 with AltiVec™ SIMD and Hardware Decimal Floating-Point acceleration ... (1 Reply)
Discussion started by: balaji_prk
1 Replies

6. Programming

C POSIX: Analyze a Boggle board using 100% CPU on a quad core.

I have written the worlds most advanced lexicon data structure in order to score a Boggle Board using a parallel algorithm. I ran into a problem. Using mutexes and condition variables did not allow me to use 100% of the CPU resources on my quad core Q9450. I wonder if the problem is that the... (8 Replies)
Discussion started by: HeavyJ
8 Replies

7. Linux Benchmarks

AMD Phenom(tm) 9950 Quad-Core Processor, Ram: 3.6 GB, Foxconn 7da-s and Linux 2.6.26-2-amd64

CPU/Speed: AMD Phenom(tm) 9950 Quad-Core Processor Ram: 3.6 GB Motherboard: Foxconn 7da-s Bus: Cache: Controller: Disk: Load: Kernel: Linux 2.6.26-2-amd64 Kernel ELF?: pgms: ============================================================== BYTE UNIX Benchmarks (Version... (0 Replies)
Discussion started by: migracho
0 Replies

8. Red Hat

How to Check Memory if Single/Dual/Quad Rank

What command in redhat linux to know your memory if it is single, dual or quad rank. Anyone? (2 Replies)
Discussion started by: Mujakol
2 Replies
CPUPOWER-FREQUENCY-INFO(1)					  cpupower Manual					CPUPOWER-FREQUENCY-INFO(1)

NAME
cpupower frequency-info - Utility to retrieve cpufreq kernel information SYNTAX
cpupower [ -c cpulist ] frequency-info [options] DESCRIPTION
A small tool which prints out cpufreq information helpful to developers and interested users. OPTIONS
-e --debug Prints out debug information. -f --freq Get frequency the CPU currently runs at, according to the cpufreq core. -w --hwfreq Get frequency the CPU currently runs at, by reading it from hardware (only available to root). -l --hwlimits Determine the minimum and maximum CPU frequency allowed. -d --driver Determines the used cpufreq kernel driver. -p --policy Gets the currently used cpufreq policy. -g --governors Determines available cpufreq governors. -a --related-cpus Determines which CPUs run at the same hardware frequency. -a --affected-cpus Determines which CPUs need to have their frequency coordinated by software. -s --stats Shows cpufreq statistics if available. -y --latency Determines the maximum latency on CPU frequency changes. -o --proc Prints out information like provided by the /proc/cpufreq interface in 2.4. and early 2.6. kernels. -m --human human-readable output for the -f, -w, -s and -y parameters. REMARKS By default only values of core zero are displayed. How to display settings of other cores is described in the cpupower(1) manpage in the --cpu option section. You can't specify more than one of the output specific options -o -e -a -g -p -d -l -w -f -y. You also can't specify the -o option combined with the -c option. FILES
/sys/devices/system/cpu/cpu*/cpufreq/ /proc/cpufreq (deprecated) /proc/sys/cpu/ (deprecated) AUTHORS
Dominik Brodowski <linux@brodo.de> - author Mattia Dongili<malattia@gmail.com> - first autolibtoolization SEE ALSO
cpupower-frequency-set(1), cpupower(1) 0.1 CPUPOWER-FREQUENCY-INFO(1)
All times are GMT -4. The time now is 01:40 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy