06-18-2010
It has been a while since I've used tape so consider the source.
IIRC, mkdev created 3 devices when it made tape. Are there other devices in /dev that could be your tape, or links to your tape.
On earlier versions you could modify /etc/default/tar to change the default line to point to the one device you use.
messages indicates that it found the drive, so I would anticipate that the issue is the name.
8 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
I have a hp d 350 running on 10.2,im having a problem with the dds2 tape drive whenever i tried backing up larger files...i have remove the tape driver and add it using sam again but still the tape drive is not working .....is there a solution to this problem?
# tar cvf /dev/rmt/0m priso.ds
a... (3 Replies)
Discussion started by: giriplug
3 Replies
2. UNIX for Dummies Questions & Answers
Hi,
I need to restore my tape backup, when I type "tape status" it gives;
status : ready beginning-of-tape write-protected
soft errors : 0
hard errors : 0
underruns : 3
but... (4 Replies)
Discussion started by: alisevA3
4 Replies
3. Solaris
I have been working on this one for a few days. Any help/advice would be greatly appreciated.
Hardware
Machine: Sun Blade 2000
Tape Drives: HP Ultrium LTO2 002 (x2) (Inside an L40)
Software
OS: Solaris 8
st.conf uncommented lines:
probe-scsi-all reports both drives.
/dev/rmt is... (2 Replies)
Discussion started by: lucesean
2 Replies
4. UNIX for Advanced & Expert Users
Hello sir
Please I just have tape blocked inside the tape drive of my server. My server have 2 tape drives configured but only one is available (rmt0). The problem is that i have a separed tape drive ready to be connected to my server and i wan to know how to make available the second tape drive ?... (0 Replies)
Discussion started by: sobnc
0 Replies
5. AIX
I have tape drive in one Lpar. when i saw that time tape is in defined state. After that i deleted the tape drive using the rmdev -R command. Then fired the cfgmgr -v command. But I am not getting the tape drive. Now the drive is even not in defined state also. It is not shown the tape drive. How... (1 Reply)
Discussion started by: pernasivam
1 Replies
6. Solaris
Hey folks,
Linux admin here, forced to use Opensolaris to try to use ufsdump/ufsrestore to get some data of some old tapes.
I've got Opensolaris 2009.06 on x86 and a Sony SDX-700V.
As a "control" experiment, I booted the system with a Linux live CD and the tape drive worked perfectly.
... (2 Replies)
Discussion started by: eddy_sysad
2 Replies
7. UNIX for Dummies Questions & Answers
Hi,
Using Redhat 5.7. I have Quantum tape drive connected to the server. I am trying to install the Netbackup software. Just wondering how can I see the Quantum is connected to the server. is any command I run to see the tape drive is connected?
I used to work on Solaris, I used to do... (1 Reply)
Discussion started by: samnyc
1 Replies
8. HP-UX
I have used ioscan -fnC tape and the system identified the tape drive. what is the command to show a listing of what is on the tape? I have used ls /dev/rmt/rmt0 to no avail. can anyone help?
Thanks in advance (10 Replies)
Discussion started by: Randydog
10 Replies
LEARN ABOUT DEBIAN
dds2index
dds2index(1) General Commands Manual dds2index(1)
NAME
dds2index - tool to create an indexfile for the use of
SYNOPSIS
dds2index [options]
DESCRIPTION
dds2index creates an index file that is required by the file extraction utility dds2tar(1). It works on tar archives stored on dds tape
devices (DAT). Since the file structure of the tape archives is used to extract the files, the archive must be an uncompressed tar ar-
chive. But compression by the transparent signal processor of the tape device is allowed.
The index created by dds2index is written to stdout by default and should normally be stored on hard disk as indexfile for later use by
dds2tar(1).
The default tape device to read from is /dev/nst0, which may be overridden with the environment variable TAPE, which in turn may be over-
ridden with the -f device option. The device must be a SCSI tape device.
OPTIONS
-f devicefile
device of the tape archive. Must be a character special file.
-t indexfile
write the index to indexfile, not to stdout.
-z,--compress
write the index in (gzip) compressed mode.
--help print some screens of online help with examples through a pager and exit immediatley.
OPTIONS you didn't really need
-b, --block-size
Set the maximal blocksize, dds2index can handle.
--z, --no-compress
Don't filter the archive file through gzip.
-v,--verbose
verbose mode. Print to stderr what is going on.
-h,--hash-mode
Print a hash sign '#' to stderr for each MB read from tape.
-V,--version
Print the version number of dds2index to stderr and exit immediately.
EXAMPLES
Example of getting the index from the default tape /dev/nst0 and storing it in file archive.idx:
dds2index -v -t archive.idx
WARNING
This program can only read records (tar is calling them tape blocks) up to 32 kbytes. A bigger buffer will cause problems with the Linux
device driver.
ENVIRONMENT
The environment variable TAPE overrides the default tape device /dev/nst0.
FILES
/dev/nst0 default tape device file. Must be a character special file.
SEE ALSO
dds2tar(1), mt(1), mt-dds(1), tar(1), gzip(1)
HISTORY
This program was created as a tool for dds2tar(1).
AUTHOR
J"org Weule (weule@cs.uni-duesseldorf.de), Phone +49 211 751409. This software is available at ftp.uni-duesseldorf.de:/pub/unix/apollo
2.4 dds2index(1)