06-18-2010
thanks for your reply. mscsi file is as follows: -
* ha = device name of SCSI host adapter driver e.g. ad
*ha attach number ID lun bus
wd Srom 1 0 0 0
blad Stp 0 6 0 0
messages report is as follows:-
device address vec dma comment
---------------------------------------------------------------------------
%adapter 0xCC00-0xCCFF 5 - type=blad ha=0 bus=0 id=7 fts=sto
%tape - - - type=S ha=0 id=6 lun=0 bus=0 ht=blad
mem: total = 261364k, kernel = 14464k, user = 246900k
swapdev = 1/41, swplo = 0, nswap = 786000, swapmem = 393000k
rootdev = 1/42, pipedev = 1/42, dumpdev = 1/41
kernel: Hz = 100, i/o bufs = 6652k
regards,
Njoroge
8 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
I have a hp d 350 running on 10.2,im having a problem with the dds2 tape drive whenever i tried backing up larger files...i have remove the tape driver and add it using sam again but still the tape drive is not working .....is there a solution to this problem?
# tar cvf /dev/rmt/0m priso.ds
a... (3 Replies)
Discussion started by: giriplug
3 Replies
2. UNIX for Dummies Questions & Answers
Hi,
I need to restore my tape backup, when I type "tape status" it gives;
status : ready beginning-of-tape write-protected
soft errors : 0
hard errors : 0
underruns : 3
but... (4 Replies)
Discussion started by: alisevA3
4 Replies
3. Solaris
I have been working on this one for a few days. Any help/advice would be greatly appreciated.
Hardware
Machine: Sun Blade 2000
Tape Drives: HP Ultrium LTO2 002 (x2) (Inside an L40)
Software
OS: Solaris 8
st.conf uncommented lines:
probe-scsi-all reports both drives.
/dev/rmt is... (2 Replies)
Discussion started by: lucesean
2 Replies
4. UNIX for Advanced & Expert Users
Hello sir
Please I just have tape blocked inside the tape drive of my server. My server have 2 tape drives configured but only one is available (rmt0). The problem is that i have a separed tape drive ready to be connected to my server and i wan to know how to make available the second tape drive ?... (0 Replies)
Discussion started by: sobnc
0 Replies
5. AIX
I have tape drive in one Lpar. when i saw that time tape is in defined state. After that i deleted the tape drive using the rmdev -R command. Then fired the cfgmgr -v command. But I am not getting the tape drive. Now the drive is even not in defined state also. It is not shown the tape drive. How... (1 Reply)
Discussion started by: pernasivam
1 Replies
6. Solaris
Hey folks,
Linux admin here, forced to use Opensolaris to try to use ufsdump/ufsrestore to get some data of some old tapes.
I've got Opensolaris 2009.06 on x86 and a Sony SDX-700V.
As a "control" experiment, I booted the system with a Linux live CD and the tape drive worked perfectly.
... (2 Replies)
Discussion started by: eddy_sysad
2 Replies
7. UNIX for Dummies Questions & Answers
Hi,
Using Redhat 5.7. I have Quantum tape drive connected to the server. I am trying to install the Netbackup software. Just wondering how can I see the Quantum is connected to the server. is any command I run to see the tape drive is connected?
I used to work on Solaris, I used to do... (1 Reply)
Discussion started by: samnyc
1 Replies
8. HP-UX
I have used ioscan -fnC tape and the system identified the tape drive. what is the command to show a listing of what is on the tape? I have used ls /dev/rmt/rmt0 to no avail. can anyone help?
Thanks in advance (10 Replies)
Discussion started by: Randydog
10 Replies
AHB(4) BSD Kernel Interfaces Manual AHB(4)
NAME
ahb -- Adaptec EISA SCSI host adapter driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device ahb
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
ahb_load="YES"
DESCRIPTION
This driver provides access to the SCSI bus connected to an Adaptec AHA-174X host adapters in ``enhanced'' mode. Tagged queueing and syn-
chronous SCSI transfers are supported.
HARDWARE
The ahb driver supports the following SCSI host adapters:
o Adaptec AHA-1740
o Adaptec AHA-1742
o Adaptec AHA-1740A
o Adaptec AHA-1742A
CAVEATS
The Adaptec 174X is very sensitive to SCSI bus termination and cable length. It may also have difficulties operating with some modern
devices that, due to their speed, expose timing problems in the controller. There are no known mechanisms for working around device incom-
patibilities of this nature.
SEE ALSO
aha(4), ahc(4), aic(4), cd(4), da(4), sa(4), scsi(4)
AUTHORS
The ahb driver was written by Justin T. Gibbs.
BSD
July 4, 2004 BSD