Sponsored Content
Full Discussion: ufsrestore T5240
Operating Systems Solaris ufsrestore T5240 Post 302429553 by rajasekg on Tuesday 15th of June 2010 12:25:14 AM
Old 06-15-2010
MySQL ufsrestore T5240

Hi,

Scsi Tape drive is connected with other Sun V440 Server, i have taken the root filesystem ufsdump through ufsdump -0uf servername:/dev/rmt/0n /

if we need to do ufsrestore the root filesystem means need to boot the server using bood cdrom -s then mount the root slice in /mnt and then ufsrestore -rvf /dev/rmt/0n

My query is if we booted the server with cdrom ( single user ) means whether i can able to access remote tape drive
ufsrestore -rvf servername:/dev/rmt/0n this command will work?

Rajasekar
 

9 More Discussions You Might Find Interesting

1. Solaris

raidctl on SUN T5240

Setting up a T5240 with two disks c1t0d0 and c1t1d0. I am trying to use raidctl but when I issue. raidctl -l I get Controller 1 Disk: 0.0.0 Disk: 0.1.0 So I try raidctl -c '0.0.0 0.1.0' -r 1 1 and I get "Array in use." I try (4 Replies)
Discussion started by: photon
4 Replies

2. Solaris

cannot plumb nxge on T5240

its a fresh installation. during the OS setup, it did not prompt for IP, netmask and gateway. using Solaris 10 08/07 update 4. I tried to plumb manually but encountered no such interface error. but nxge interfaces can be greped from the /etc/path_to_inst file. getting similar error on... (3 Replies)
Discussion started by: incredible
3 Replies

3. Solaris

T5240 netmgmt port not blinking

I was trying to configure the netmgmt from the serial and set commitpending to true. However, the netmgmt port is not up and blinking. I tried to connect using my notebook directly to the netmgmt port and am not able to ping as well. Previouly i was doing the firmware upgrade using the webconsole.... (20 Replies)
Discussion started by: incredible
20 Replies

4. Solaris

SUN T5240 vs M3000

Hi, We are planning to buy new server for our data center. Sun T5240 or M3000 which one have better performance, we are going to create many dt sessions in this server. So, i need your suggestions. RJS (4 Replies)
Discussion started by: rajasekg
4 Replies

5. Solaris

Bizarre Sun T5240 behavior

Hi - I have a T5240 with 7 LDOMS configured. One night, network comm was broken somehow. Nobody was doing anything on the machine at the time. Here is what I saw in messages: WARNING: nxge3 : nxge_dma_mem_alloc: ddi_dma_mem_alloc kmem alloc failed WARNING: nxge3 : nxge_alloc_rx_buf_dma:... (2 Replies)
Discussion started by: pyroman
2 Replies

6. Solaris

Disable multithreading option on T5240

Hi Gurus Can any one tell me the process of disabling the multithreading option on T5240 server and my OS is on LDOM, having one physical processor with 8 core & 8 thread per core Regards (3 Replies)
Discussion started by: amity
3 Replies

7. Solaris

Cannot configure RAID on T5240

Hi ! I've been given a T5240 with 4 disks and 2 HBA cards (but no array connected). I did a factory reset on SP and NVRAM clean on OBP because the server had been used before. I boot cdrom in single mode and try to create a hw mirror with disks from c1... but only c2 is seen by raidctl. ... (2 Replies)
Discussion started by: delavega
2 Replies

8. Solaris

Question: # of ldoms on T5240 with 2 T2 US 8 core

I have a T5240 with 2 T2 US 8 core.. Theoretically how many ldoms can I configure? (5 Replies)
Discussion started by: Iftikhar Barrie
5 Replies

9. Solaris

Using a Modem on a T5-2 or a T5240

Hi Folks, Just a quick question - hopefully! I have an application currently running on a V890 with Solaris 9, I'd like to move this to either one of our T-5's or one of the T5240's in a Legacy container on an LDOM - but the fly in the ointment is the application still uses a standard Hayes... (3 Replies)
Discussion started by: gull04
3 Replies
FC_REMOTE_PORT_ADD(9)						  SCSI mid layer					     FC_REMOTE_PORT_ADD(9)

NAME
fc_remote_port_add - notify fc transport of the existence of a remote FC port. SYNOPSIS
struct fc_rport * fc_remote_port_add(struct Scsi_Host * shost, int channel, struct fc_rport_identifiers * ids); ARGUMENTS
shost scsi host the remote port is connected to. channel Channel on shost port connected to. ids The world wide names, fc address, and FC4 port roles for the remote port. DESCRIPTION
The LLDD calls this routine to notify the transport of the existence of a remote port. The LLDD provides the unique identifiers (wwpn,wwn) of the port, it's FC address (port_id), and the FC4 roles that are active for the port. For ports that are FCP targets (aka scsi targets), the FC transport maintains consistent target id bindings on behalf of the LLDD. A consistent target id binding is an assignment of a target id to a remote port identifier, which persists while the scsi host is attached. The remote port can disappear, then later reappear, and it's target id assignment remains the same. This allows for shifts in FC addressing (if binding by wwpn or wwnn) with no apparent changes to the scsi subsystem which is based on scsi host number and target id values. Bindings are only valid during the attachment of the scsi host. If the host detaches, then later re-attaches, target id bindings may change. This routine is responsible for returning a remote port structure. The routine will search the list of remote ports it maintains internally on behalf of consistent target id mappings. If found, the remote port structure will be reused. Otherwise, a new remote port structure will be allocated. Whenever a remote port is allocated, a new fc_remote_port class device is created. Should not be called from interrupt context. NOTES
This routine assumes no locks are held on entry. AUTHORS
James Bottomley <James.Bottomley@hansenpartnership.com> Author. Rob Landley <rob@landley.net> Author. COPYRIGHT
Kernel Hackers Manual 3.10 June 2014 FC_REMOTE_PORT_ADD(9)
All times are GMT -4. The time now is 02:30 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy