Hi,
based on your experience what is the most common IPMP configuration on a two nodes cluster for HA failover / scalable services?
...active-active, active-standby with probe-based failure detection etc.
Thanks (3 Replies)
Hi,
I've a problem when try to detach nic e1000g1.
IPMP configuration:
# ifconfig -a
...cut...
e1000g1: flags=1000842<BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 7
inet 0.0.0.0 netmask 0
ether 0:c:29:67:16:ef
e1000g2: flags=1000842<BROADCAST,RUNNING,MULTICAST,IPv4>... (3 Replies)
Hi all,
Currently i got a server which had two interface. I had study the <SystemAdministration Guide: IP> but still donno what is the correct step to configure it. Can u all help me on it? thanks
# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index... (6 Replies)
Hi all,
I am new to HACMP. So sorry for the newie question. But I did search the forum and it seems that no one asks this before.
So if a 2-node cluster runs in active-active mode (and the same application), what is the benefit of using HACMP ?
If it runs in active-stanby, it is easy to... (9 Replies)
Dear All,
I have configured IPMP in one of my SUN machine which is having solros 9 version. I have updated all files like /etc/hosts,/etc/hostname.ce0 and /etc/hostname.ce1 and rebooted the server. But IP's are not mounted which i have given in /etc/hosts file.
Please find the below ifconfig... (6 Replies)
Hi,
I need to configure 4 ip address (same subnet and mask) in one ipmp group (two interfaces) in an active active formation (link based). Can some one provide the steps or a tutorial link.
Thanks (2 Replies)
Hi All, We are using solaris samba server for our company project to provide access to code to our development team.Recently our ICT has disabled wins service on Active directory due which user are not able to connect to samba share and they are getting error "No logon server available" as samba... (2 Replies)
#!/bin/bash
for digit in $(seq 1 10)
do
if ping -c1 -w2 192.168.1.$digit &> /dev/null
then
echo "192.168.1.$digit is UP"
else
echo "192.168.1.$digit is DOWN"
fi
done (3 Replies)
Hi,
I have two physical interface connected to solaris box.
1. e1000g1
2. e1000g2
I have added these interfaced under a same IPMP group "IPMP1"
After that I have configured a test address for e1000g1 like below
ifconfig e1000g1 addif <ip-address> netmask + broadcast + -failover... (1 Reply)
Discussion started by: praveensharma21
1 Replies
LEARN ABOUT LINUX
if_mpadm
if_mpadm(1M) System Administration Commands if_mpadm(1M)NAME
if_mpadm - change operational status of interfaces within a multipathing group
SYNOPSIS
/usr/sbin/if_mpadm -d interface_name
/usr/sbin/if_mpadm -r interface_name
DESCRIPTION
Use the if_mpadm utility to change the operational status of interfaces that are part of an IP multipathing group. If the interface is
operational, you can use if_mpadm -d to detach or off-line the interface. If the interface is off-lined, use if_mpadm -r to revert it to
its original state.
When a network interface is off-lined, all network access fails over to a different interface in the IP multipathing group. Any addresses
that do not failover are brought down. Network access includes unicast, broadcast, and multicast for IPv4 and unicast and multicast for
IPv6. Addresses marked with IFF_NOFAILOVER do not failover. They are marked down. After an interface is off-lined, the system will not use
the interface for any outbound or inbound traffic, and the interface can be safely removed from the system without any loss of network
access.
The if_mpadm utility can be applied only to interfaces that are part of an IP multipathing group.
OPTIONS
The if_mpadm utility supports the following options:
-d interface_name Detach or off-line the interface specified by interface_name.
-r interface_name Reattach or undo the previous detach or off-line operation on the interface specified by interface_name. Unless
the -d option was used to detach or off-line the interface, this option will fail.
EXAMPLES
Example 1: Detaching an Interface
Use the following command to off-line or detach the interface. All network access will failover from hme0 to other interfaces in the same
IP multipathing group. If no other interfaces are in the same group, the operation will fail.
example% if_mpadm -d hme0
Example 2: Reattaching an Off-line Interface
Use the following command to undo the previous operation. Network access will failback to hme0.
example% if_mpdadm -r hme0
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
|Interface Stability |Unstable |
+-----------------------------+-----------------------------+
SEE ALSO ifconfig(1M), in.mpathd(1M), attributes(5)DIAGNOSTICS
off-line failed as there is no other functional interface available in the multipathing group for failing over the network access.
This message means that other interfaces in the group are failed over already or the multipathing configuration was not suitable for com-
pleting a failover.
off-line cannot be undone because multipathing configuration is not consistent across all the interfaces in the group.
This message means that some interfaces in the IP multipathing group are not configured consistently with other interfaces in the group,
for example, one of the interfaces in the group does not have an IFF_NOFAILOVER address.
SunOS 5.10 3 Sep 2002 if_mpadm(1M)