:mad: I did this the other day but one of my support personnel removed my history so i could call it back up to remeber the exact command since i am air-headed at times. I am trying to take a 30 MEG file off the system and drop it to tape then i want to make the file go back to being 0 bytes so... (1 Reply)
I have tried winscp, filezilla to copy data from windows xp SP2 machine to the sun sparc unix machine. However speed is around 120 to 130 kb/sec. I do have lot of files & with large size.
So I switched to windows command prompt & transfered few files using sftp command. Its very fast as compared... (0 Replies)
Hello,
I have two files file1 & file2 containing both lines (1 word per line). I need to extract the lines that are in file1 and not present in file2 and have the result in output file.
i.e :
user>cat file1
line1
line2
line3
line4
line5
user>cat file2
line1
line3
line5
The... (2 Replies)
Hi, I have 7 terabytes of tar files, one for every single day since 1980. Inside these tar files are GRIB files, each with 100+ variables. There's 8 GRIBs in each tar, corresponding to different times of the day. I need 6 friggin variables..., and it takes TWO WEEKS TO EXTRACT ALL THE TAR FILES... (3 Replies)
Hi all,
My sample file is something like this,
ORA-00206: Message 206 not found; product=RDBMS; facility=ORA
ORA-00202: Message 202 not found; product=RDBMS; facility=ORA
ORA-27063: Message 27063 not found; product=RDBMS; facility=ORA
ORA-00206: Message 206 not found; ... (1 Reply)
Hi,
I want to untar all log files from following tarred directory hierarchy
Log_files.tar.gz/subject*.tar.gz/project*/*.log
It means there are subject1.tar.gz to subject9.tar.gz and in those tarred subect directories there are project1 - project5 directories and in those directories there... (2 Replies)
Hi,
I have some files that i want to concatene and put each of lines of this files on a specific position :
File1
AAAAAAA
BBBBBBB
CCCCCCC
File2
DDDDDDD
EEEEEEE
FFFFFFF
File3
GGGGGG
HHHHHH
IIIIII
New file (6 Replies)
Hi
here is my code
for i in `ls *.cmd`
do
msg
aaa imp -U$AAAUSER -P$AAAUSERPWD <$i>>$curdir/import_tap.out -Jutf8
done
I can only get all files with .cmd extension. what i need to get are all the files inside the specific folder
Thanks (2 Replies)
Discussion started by: cmarzan
2 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)