06-04-2010
Hi,
Thanks for the response..I am actually looking for the files which stores IP and gateway related information ,like in RHEL below files holds the information about IP and gateway.
/etc/sysconfig/network ; config file holds the gateway and domain information
/etc/sysconfig/network-scripts/ifcfg-ethx ;config file holds the information about IP address .
Thanks,
Sunil.K
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. BSD
hi
howto restart the network with a wireless interface including wpa_supplicant on freeBSD 7.2 without reboot? (3 Replies)
Discussion started by: ccc
3 Replies
3. AIX
Hi,
I am trying to list all the interface present in the given system.
Here is sample program.
i.e. cat 1.c
#include <sys/types.h>
#include <sys/socket.h>
#include <sys/ioctl.h>
#include <sys/dlpi.h>
#include <net/if.h>
/*#include <sys/sockio.h>*/
#include <unistd.h>
#include... (3 Replies)
Discussion started by: jgobbur
3 Replies
4. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
5. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
6. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
7. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
8. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
9. Red Hat
Hi,
I have 2 machines in production environment:
1. redhat machine for application
2. DB machine (oracle)
The application doing a lot of small read&writes from and to the DB machine.
The problem is that after some few hours the network from the application to the DB becomes very slow and... (4 Replies)
Discussion started by: moshesa
4 Replies
10. Debian
Hello,
I would like to do follow steps.
Set a static IP-Adress on eth0 (For Testing)
Set DHCP on eth0
All steps should be done without a single reboot.
/etc/network/interfaces
iface eth0 inet static
address 192.0.2.7/24
gateway 192.0.2.254How do i perform... (3 Replies)
Discussion started by: int3g3r
3 Replies
LEARN ABOUT SUSE
ifcfg-vlan
IFCFG-VLAN(5) Network configuration IFCFG-VLAN(5)
NAME
ifcfg-vlan - virtual LAN interface configuration
SYNOPSIS
/etc/sysconfig/network/ifcfg-vlan*
Virtual LANs (802.1q)
To setup a vlan interface you need a configuration file that contains at least the mandatory
ETHERDEVICE
variable with the real interface used for the virtual LAN.
Further, it may contain the optional
VLAN_ID
variable that specifies the VLAN ID.
By default and when the VLAN_ID variable is not set, the number at the end of the interface name is the VLAN ID.
Preferably the interface name and the configuration file follow the VLAN interface name scheme (type), that is either:
ifcfg-vlan<VLAN-ID> (e.g. ifcfg-vlan42)
or
ifcfg-name.<VLAN-ID> (e.g. ifcfg-eth0.42)
The VLAN-ID can be also 0-padded (e.g. ifcfg-vlan0042 or ifcfg-eth0.0042).
Also in case of custom names, trailing digits are interpreted as VLAN-ID by default (e.g. ifcfg-dmz42). When VLAN_ID is set in the config,
the interface name have any name (e.g. ifcfg-foobar).
Note: The drawback of custom interface names and VLAN_ID usage is, that a rename of the interface is required and that they violate the
name scheme.
The real interface will be set UP automatically and doesn't need a config file in case of a physical interface. But without a config file
YaST will consider this interface as unused, if will not follow hotplug events and you're unable to apply any settings, e.g. ETH-
TOOL_OPTIONS. To avoid that, provide an config file with at least STARTMODE='auto'.
The rest of the VLAN interface IP and routes configuration do not differ from ordinary interfaces. See also man ifcfg and man routes for
details.
EXAMPLES
Sets up vlan3 vlan interface on top of eth0:
ifcfg-vlan3
STARTMODE='auto'
ETHERDEVICE='eth0'
IPADDR='192.168.3.27/24'
Sets up eth0.3 vlan interface on top of eth0:
ifcfg-eth0.3
STARTMODE='auto'
ETHERDEVICE='eth0'
IPADDR='192.168.3.27/24'
Sets up lan1 vlan interface with ID 42 on top of eth0:
ifcfg-lan1
STARTMODE='auto'
ETHERDEVICE='eth0'
VLAN_ID='42'
IPADDR='192.168.3.27/24'
BUGS
Please report bugs at <http://www.suse.de/feedback>
AUTHOR
Christian Zoz <zoz@suse.de>
Michal Svec <msvec@suse.cz>
Bjoern Jacke
Mads Martin Joergensen <mmj@suse.de>
Michal Ludvig <mludvig@suse.cz>
Marius Tomaschewski <mt@suse.de>
SEE ALSO
routes(5), ifcfg(5), ifup(8).
sysconfig August 2004 IFCFG-VLAN(5)