Sponsored Content
Operating Systems AIX How restart the network interface in AIX? Post 302426910 by ross.mather on Thursday 3rd of June 2010 09:05:56 AM
Old 06-03-2010
If you are unsure best to set all the TCP/IP settings using smitty TCP/IP.

Iff you are changing the default gateway on the command line you will need to remove the old default gateway first before adding the new one.

To put an IP address on an interface:
Code:
chdev -l en6 -a netaddr=9.9.9.9 -a netmask=255.255.255.0 -a state=up


To add a route to the routing table:
Code:
chdev -l inet0 -a route=net,-hopcount,0,-netmask,255.255.255.0,-if,en5,,,,-static,9.9.8.0,9.9.9.1

To remove the same route from the routing table
Code:
chdev -l inet0 -a delroute=net,-hopcount,0,-netmask,255.255.255.0,-if,en5,,,,-static,9.9.8.0,9.9.9.1

You can see what the route table should be with:
Code:
lsattr -El inet0

 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt (4 Replies)
Discussion started by: witt
4 Replies

2. BSD

restart the network on freeBSD 7.2

hi howto restart the network with a wireless interface including wpa_supplicant on freeBSD 7.2 without reboot? (3 Replies)
Discussion started by: ccc
3 Replies

3. AIX

AIX platform: network interface list

Hi, I am trying to list all the interface present in the given system. Here is sample program. i.e. cat 1.c #include <sys/types.h> #include <sys/socket.h> #include <sys/ioctl.h> #include <sys/dlpi.h> #include <net/if.h> /*#include <sys/sockio.h>*/ #include <unistd.h> #include... (3 Replies)
Discussion started by: jgobbur
3 Replies

4. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies

5. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies

6. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies

7. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies

8. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies

9. Red Hat

Network becomes slow and return fast only after restart network

Hi, I have 2 machines in production environment: 1. redhat machine for application 2. DB machine (oracle) The application doing a lot of small read&writes from and to the DB machine. The problem is that after some few hours the network from the application to the DB becomes very slow and... (4 Replies)
Discussion started by: moshesa
4 Replies

10. Debian

How do i correct restart network-services in Debian?

Hello, I would like to do follow steps. Set a static IP-Adress on eth0 (For Testing) Set DHCP on eth0 All steps should be done without a single reboot. /etc/network/interfaces iface eth0 inet static address 192.0.2.7/24 gateway 192.0.2.254How do i perform... (3 Replies)
Discussion started by: int3g3r
3 Replies
USERNETCTL(8)						      System Manager's Manual						     USERNETCTL(8)

NAME
usernetctl - allow a user to manipulate a network interface if permitted SYNOPSIS
usernetctl interface-name up|down|report DESCRIPTION
usernetctl checks to see if users are allowed to manipulate the network interface specified by interface-name, and then tries to bring the network interface up or down, if up or down was specified on the command line, or returns true or false status (respectively) if the report option was specified. usernetctl is not really meant to be called directly by users, though it currently works fine that way. It is used as a wrapper by the ifup and ifdown scripts, so that users can do exactly the same thing as root: ifup interface-name ifdown interface-name and ifup and ifdown will call usernetctl automatically to allow the interface status change. OPTIONS
interface-name The name of the network interface to check; for example, "ppp0". For backwards compatibility, "ifcfg-ppp0" and "/etc/sysconfig/net- work-scripts/ifcfg-ppp0" are also supported. up|down Attempt to bring the interface up or down. report Report on whether users can bring the interface up or down. NOTES
Alternate device configurations may inherit the default configuration's permissions. RHS
Red Hat, Inc. USERNETCTL(8)
All times are GMT -4. The time now is 04:24 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy