06-03-2010
Hi,
Yes I can see /etc/vfstab and /etc/passwd files.
I tried to unplug the power cable and plugging again but it didn't work.
Thanks
Pradeep
9 More Discussions You Might Find Interesting
1. Solaris
Hi All,
I have new Netra 240 box which is not detecting its harddisk equiped with itse same har disk are detected when I swap with another machine.
Same time If I swap hardisk of other machine to this Netra 240 box, also do not work. I have checked chassis, cabling etc and all looks fine. ... (1 Reply)
Discussion started by: xpwistler
1 Replies
2. Solaris
so i've grabbed this sun netra t1 for some small dev work. now obviously i need to install sol10. no problem done it a million times except for the fact that i've never actually done it w/o a term server. so i grab a usb to serial and a serial to rj45 (the one you get in every cisco order.. roll... (24 Replies)
Discussion started by: pupp
24 Replies
3. Solaris
Hi,
sunfire v240 and netra 240 are looks similar. system board, memory and processors are similar, then why netra 240 called as telco server?
can anyone tell the difference.
RJS (1 Reply)
Discussion started by: rajasekg
1 Replies
4. UNIX for Dummies Questions & Answers
Hello everyone,
I'm extremely new when it comes to SUN servers so bear with me and hopefully I can describe the issue I have accurately.
At work we just received a refurbished SUN Netra 240 server. I was told to change some of the EEprom settings, and to do that I was to use a... (0 Replies)
Discussion started by: afferbwt
0 Replies
5. Solaris
I am trying to use a serial communications device that is connected to /dev/ttyb on a netra 240 server. This is a solaris zone configuration using solaris 10 0910. I am able to access /dev/ttyb from the global zone but not throught he non-global zone. I have enabled all of the tty devices in my... (0 Replies)
Discussion started by: disagreeable
0 Replies
6. Hardware
Hi guys,
when I power on my sun netra 240 server,
it displays these error messages:
1. Notice: cpu 0 has 2048/2048 MB of memory disabled.
2. Error : The following devices are disabled dimm1.
Please can anyone be kind enough to explain this for me?
Thanks (2 Replies)
Discussion started by: cjashu
2 Replies
7. Solaris
Hello all,
I recently powered on my Netra AX1105 server only to be greeted with the following error message. I am not sure what to do here,
I cant fun fsck on OK prompt.. did ok>boot -r and now it keeps booting from net, then I run ok>boot disk then outputs the following message... and keeps... (3 Replies)
Discussion started by: br1an
3 Replies
8. Solaris
Hi Guys,
Could someone please share the dvd/cd that came with server Netra x4200 M2 since it is not more available in Oracle site? Or do you know where I can get that?
Thanks! (4 Replies)
Discussion started by: CristianS
4 Replies
9. Solaris
Hi,
One of my Netra 240 went into hung state and I had to reboot it. I powered it off and tried booting it again but unsuccessful. It is not connected to SAN and have local disks. Not able to boot in failsafe mode too.
There are two disks of 72GB, both are mirrored in SVM. It complains about... (5 Replies)
Discussion started by: solaris_1977
5 Replies
LEARN ABOUT ULTRIX
iostat
iostat(1) General Commands Manual iostat(1)
Name
iostat - report I/O statistics
Syntax
iostat [ -c ] [ -t ] [ disknames ] [ interval ] [ count ]
Description
The command reports I/O statistics for terminals, disks and cpus. For terminals the number of input and output characters are counted.
For disks the number of 512 byte blocks per second and number of transfers per second are displayed. For cpus, it provides the percentage
of time the system has spent in user mode, in user mode running low priority (niced) processes, in system mode, and idling. On multipro-
cessor systems these cpu statistics represent a cumulative summary of all the cpus.
The optional disknames argument causes disk statistics to be displayed for the specified disks. If this argument is not specified then
disk statistics will be displayed for the first 3 disks only.
The optional interval argument causes to report once each interval seconds. The first report is for all time since a reboot and each sub-
sequent report is for the last interval only.
The optional count argument restricts the number of reports.
Options
-c Displays the percentage of time each cpu spent in user mode, running low priority (nice'd) processes, in system mode, and idling.
-t Displays the number of characters read from and written to terminals.
Examples
This example will cause cpu and disk statistics for the 5 disks ra0, ra1, ra2, ra3, and ra4.
iostat ra0 ra1 ra2 ra3 ra4
This example will cause cpu, terminal, and disk statistics for ra0 to be displayed and updated every 2 seconds.
iostat -t ra0 2
Files
See Also
vmstat(1), cpustat(1)
iostat(1)