06-03-2010
Hi,
Yes I can see /etc/vfstab and /etc/passwd files.
I tried to unplug the power cable and plugging again but it didn't work.
Thanks
Pradeep
9 More Discussions You Might Find Interesting
1. Solaris
Hi All,
I have new Netra 240 box which is not detecting its harddisk equiped with itse same har disk are detected when I swap with another machine.
Same time If I swap hardisk of other machine to this Netra 240 box, also do not work. I have checked chassis, cabling etc and all looks fine. ... (1 Reply)
Discussion started by: xpwistler
1 Replies
2. Solaris
so i've grabbed this sun netra t1 for some small dev work. now obviously i need to install sol10. no problem done it a million times except for the fact that i've never actually done it w/o a term server. so i grab a usb to serial and a serial to rj45 (the one you get in every cisco order.. roll... (24 Replies)
Discussion started by: pupp
24 Replies
3. Solaris
Hi,
sunfire v240 and netra 240 are looks similar. system board, memory and processors are similar, then why netra 240 called as telco server?
can anyone tell the difference.
RJS (1 Reply)
Discussion started by: rajasekg
1 Replies
4. UNIX for Dummies Questions & Answers
Hello everyone,
I'm extremely new when it comes to SUN servers so bear with me and hopefully I can describe the issue I have accurately.
At work we just received a refurbished SUN Netra 240 server. I was told to change some of the EEprom settings, and to do that I was to use a... (0 Replies)
Discussion started by: afferbwt
0 Replies
5. Solaris
I am trying to use a serial communications device that is connected to /dev/ttyb on a netra 240 server. This is a solaris zone configuration using solaris 10 0910. I am able to access /dev/ttyb from the global zone but not throught he non-global zone. I have enabled all of the tty devices in my... (0 Replies)
Discussion started by: disagreeable
0 Replies
6. Hardware
Hi guys,
when I power on my sun netra 240 server,
it displays these error messages:
1. Notice: cpu 0 has 2048/2048 MB of memory disabled.
2. Error : The following devices are disabled dimm1.
Please can anyone be kind enough to explain this for me?
Thanks (2 Replies)
Discussion started by: cjashu
2 Replies
7. Solaris
Hello all,
I recently powered on my Netra AX1105 server only to be greeted with the following error message. I am not sure what to do here,
I cant fun fsck on OK prompt.. did ok>boot -r and now it keeps booting from net, then I run ok>boot disk then outputs the following message... and keeps... (3 Replies)
Discussion started by: br1an
3 Replies
8. Solaris
Hi Guys,
Could someone please share the dvd/cd that came with server Netra x4200 M2 since it is not more available in Oracle site? Or do you know where I can get that?
Thanks! (4 Replies)
Discussion started by: CristianS
4 Replies
9. Solaris
Hi,
One of my Netra 240 went into hung state and I had to reboot it. I powered it off and tried booting it again but unsuccessful. It is not connected to SAN and have local disks. Not able to boot in failsafe mode too.
There are two disks of 72GB, both are mirrored in SVM. It complains about... (5 Replies)
Discussion started by: solaris_1977
5 Replies
LEARN ABOUT SUNOS
optiups
OPTIUPS(8) NUT Manual OPTIUPS(8)
NAME
optiups - Driver for Opti-UPS (Viewsonic) UPS and Zinto D (ONLINE-USV) equipment
NOTE
This man page only documents the hardware-specific features of the optiups driver. For information about the core driver, see nutupsdrv(8).
SUPPORTED HARDWARE
optiups was originally written against a PowerES 280es in nut-0.45. It was revised for nut-2.0.1 and tested against a PowerES 420E. It is
expected to work with at least the PowerES, PowerPS, and PowerVS models.
This driver additionally supports a Zinto D from ONLINE USV-Systeme AG because of their very similar commands, but it is unknown if it also
works with other UPS from them.
This driver will not work with the PowerES stock serial cable. You will need to construct your own three conductor cable:
UPS 6 -> PC 3
UPS 9 -> PC 2
UPS 4 -> PC 5
The cable for Online-USV uses pin UPS 7 (not UPS 4) -> PC 5.
EXTRA ARGUMENTS
This driver supports the following optional settings in the ups.conf(5) file:
status_only
Only poll for critical status information. Without this, optiups (and all NUT drivers) poll all sorts of information from the UPS
fairly often. It is probably not often enough to hurt anything, so this option probably is not very useful, unless you have a flaky
serial connection or a highly loaded machine.
nowarn_noimp
Does not print warnings when the UPS reports that a variable is not implemented or not pollable. Without the option you will get a
message sent to your system logs each time NUT polls the UPS. If you specify nowarn_noimp, this message will only be logged once.
fake_lowbatt
This forces the low battery flag true. Without it, if you want to test your UPS, you will have to unplug it and wait until the battery
drops to a low/critical voltage level before NUT will respond and power down your system. With the flag, NUT should power down the
system soon after you pull the plug. When you are done testing, you should remove this flag.
For basic shutdown configuration testing, the command upsmon -c fsd is preferred.
powerup
Zinto D from ONLINE-USV cannot be identified when switched to standby. Set this flag to allow the driver to power-up your Zinto UPS.
This will also power-up your equipment connected to the UPS!
BUGS
On the 420E, ups.serial and ups.temperature are unsupported features. This is not a bug in NUT or the NUT driver, just the way things are
with this UPS.
AUTHOR
Russell Kroll, Scott Heavner, Matthias Goebl
SEE ALSO
The core driver:
nutupsdrv(8)
Internet resources:
The NUT (Network UPS Tools) home page: http://www.networkupstools.org/
Network UPS Tools 05/21/2012 OPTIUPS(8)