SUN Netra 240 Boot error Post: 302426903

9 More Discussions You Might Find Interesting

1. Solaris

Netra 240 Hard disk are not detected

Hi All, I have new Netra 240 box which is not detecting its harddisk equiped with itse same har disk are detected when I swap with another machine. Same time If I swap hardisk of other machine to this Netra 240 box, also do not work. I have checked chassis, cabling etc and all looks fine. ...

2. Solaris

sun netra t1

so i've grabbed this sun netra t1 for some small dev work. now obviously i need to install sol10. no problem done it a million times except for the fact that i've never actually done it w/o a term server. so i grab a usb to serial and a serial to rj45 (the one you get in every cisco order.. roll...

3. Solaris

netra 240 difference

Hi, sunfire v240 and netra 240 are looks similar. system board, memory and processors are similar, then why netra 240 called as telco server? can anyone tell the difference. RJS

4. UNIX for Dummies Questions & Answers

Refurbished Netra 240 servers hangs after POST test

Hello everyone, I'm extremely new when it comes to SUN servers so bear with me and hopefully I can describe the issue I have accurately. At work we just received a refurbished SUN Netra 240 server. I was told to change some of the EEprom settings, and to do that I was to use a...

5. Solaris

Unable to access serial port from non-global solaris zone on netra 240

I am trying to use a serial communications device that is connected to /dev/ttyb on a netra 240 server. This is a solaris zone configuration using solaris 10 0910. I am able to access /dev/ttyb from the global zone but not throught he non-global zone. I have enabled all of the tty devices in my...

6. Hardware

POST displays error sparc netra 240

Hi guys, when I power on my sun netra 240 server, it displays these error messages: 1. Notice: cpu 0 has 2048/2048 MB of memory disabled. 2. Error : The following devices are disabled dimm1. Please can anyone be kind enough to explain this for me? Thanks

7. Solaris

Fsck: alignment error Solaris 8, SUN Netra AX11505

Hello all, I recently powered on my Netra AX1105 server only to be greeted with the following error message. I am not sure what to do here, I cant fun fsck on OK prompt.. did ok>boot -r and now it keeps booting from net, then I run ok>boot disk then outputs the following message... and keeps...

8. Solaris

SUn Netra X4200 M2 Drivers

Hi Guys, Could someone please share the dvd/cd that came with server Netra x4200 M2 since it is not more available in Oracle site? Or do you know where I can get that? Thanks!

9. Solaris

Fibre Channel link not ready on Netra 240

Hi, One of my Netra 240 went into hung state and I had to reboot it. I powered it off and tried booting it again but unsuccessful. It is not connected to SAN and have local disks. Not able to boot in failsafe mode too. There are two disks of 72GB, both are mirrored in SVM. It complains about...

LEARN ABOUT CENTOS

reboot

HALT(8) 							       halt								   HALT(8)

NAME

       halt, poweroff, reboot - Halt, power-off or reboot the machine

SYNOPSIS

       halt [OPTIONS...]

       poweroff [OPTIONS...]

       reboot [OPTIONS...]

DESCRIPTION

       halt, poweroff, reboot may be used to halt, power-off or reboot the machine.

OPTIONS

       The following options are understood:

       --help
	   Prints a short help text and exits.

       --halt
	   Halt the machine, regardless of which one of the three commands is invoked.

       -p, --poweroff
	   Power-off the machine, regardless of which one of the three commands is invoked.

       --reboot
	   Reboot the machine, regardless of which one of the three commands is invoked.

       -f, --force
	   Force immediate halt, power-off, reboot. Do not contact the init system.

       -w, --wtmp-only
	   Only write wtmp shutdown entry, do not actually halt, power-off, reboot.

       -d, --no-wtmp
	   Do not write wtmp shutdown entry.

       --no-wall
	   Do not send wall message before halt, power-off, reboot.

EXIT STATUS

       On success, 0 is returned, a non-zero failure code otherwise.

NOTES

       These are legacy commands available for compatibility only.

SEE ALSO

       systemd(1), systemctl(1), shutdown(8), wall(1)

systemd 208																   HALT(8)