06-03-2010
How restart the network interface in AIX?
Hi All,
Please let me know the command to restart the network interface and enable it on boot in AIX, similar to /etc/init.d/network restart in Redhat.
Thanks,
Sunil.K
Moderator's Comments:
|
|
please watch out to post in the right subforum!
|
|
Last edited by DukeNuke2; 06-03-2010 at 04:02 AM..
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. BSD
hi
howto restart the network with a wireless interface including wpa_supplicant on freeBSD 7.2 without reboot? (3 Replies)
Discussion started by: ccc
3 Replies
3. AIX
Hi,
I am trying to list all the interface present in the given system.
Here is sample program.
i.e. cat 1.c
#include <sys/types.h>
#include <sys/socket.h>
#include <sys/ioctl.h>
#include <sys/dlpi.h>
#include <net/if.h>
/*#include <sys/sockio.h>*/
#include <unistd.h>
#include... (3 Replies)
Discussion started by: jgobbur
3 Replies
4. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
5. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
6. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
7. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
8. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
9. Red Hat
Hi,
I have 2 machines in production environment:
1. redhat machine for application
2. DB machine (oracle)
The application doing a lot of small read&writes from and to the DB machine.
The problem is that after some few hours the network from the application to the DB becomes very slow and... (4 Replies)
Discussion started by: moshesa
4 Replies
10. Debian
Hello,
I would like to do follow steps.
Set a static IP-Adress on eth0 (For Testing)
Set DHCP on eth0
All steps should be done without a single reboot.
/etc/network/interfaces
iface eth0 inet static
address 192.0.2.7/24
gateway 192.0.2.254How do i perform... (3 Replies)
Discussion started by: int3g3r
3 Replies
LEARN ABOUT DEBIAN
lighty-enable-mod
LIGHTYENABLEMOD(1) General Commands Manual LIGHTYENABLEMOD(1)
NAME
lighty-enable-mod, lighty-disable-mod - enable or disable configuration in lighttpd server
SYNOPSIS
lighty-enable-mod [module]
lighty-disable-mod [module]
DESCRIPTION
This manual page documents briefly the lighty-enable-mod and lighty-disable-mod commands.
lighty-enable-mod and lighty-disable-mod are programs that enable (and respectively disable) the specified configuration file within
lighttpd configuration.
Both programs can be run interactively or from command line. If either program is called without any arguments, an input prompt is dis-
played to the user, where he might choose among available lighttpd modules. Immediate action is taken, if a module name was given on the
command line.
EXIT STATUS
Both programs indicate failure in their exit status. lighty-enable-mod or lighty-disable-mod respectively may leave execution with one of
the following exit codes:
0 denotes success
1 denotes a fatal error (e.g., a module could not be enabled, or a dependency was not found)
2 denotes a minor flaw (e.g., a module was not enabled because it was already loaded before)
Note
You can (un-) load several modules at time. The exit status will only reflect the most serious issue (where a minor flaw beats no error,
but a fatal error beats a minor flaw). This means, if a minor flaw was encountered as well as a fatal error, the program will leave with
exit status 1 and stop immediately.
DEPENDENCIES
Debian allows lighttpd modules to formulate dependencies to other modules they depend on. Configuration files are scanned for dependencies
upon load or unload of modules, not at runtime of the web server. Such a magic line has the following format:
# -*- depends: module[, module] -*-
and may appear anywhere in the file. If such a line is found, the extracted name is interpreted as dependency to another lighttpd module.
lighty-enable-mod will seek available configurations to satisfy this dependency and will recursively enable all dependencies found on its
way. lighty-disable-mod will disable reverse dependencies recursively.
SEE ALSO
lighttpd(1)
AUTHOR
Program and man pages were originally written by Krzysztof Krzyaniak <eloy@debian.org> and later modified by Arno Toll <debian@toell.net>
2006-01-11 LIGHTYENABLEMOD(1)