05-26-2010
as per my knowledge....
just add routes
#route add default 10.8.10.1
then ping 10.8.10.1
10 More Discussions You Might Find Interesting
1. IP Networking
We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command
64 bytes from 124.168.215.40:... (6 Replies)
Discussion started by: chrisanto_2000
6 Replies
2. IP Networking
Hello this is my first post at this forum.
Apologize for my lack of network understanding
but Im posting to learn.
I have a problem reaching default gateway 10.18.110.1
If I use my laptop I can ping 10.18.110.1 but with our red hat multihomed server the gateway does not respond to ping.
cat... (11 Replies)
Discussion started by: vettec3
11 Replies
3. Solaris
I was install new solaris10 on m4000 model after that i "ping -s" to default gateway but it's take longtime (2 Min) to reply and if i use "ping" only it's reply to fase(2 sec). any body who can tell me about my problem and how to fix it please. i'm try to fix several days. (2 Replies)
Discussion started by: cesmk
2 Replies
4. AIX
Hello,
I am new to Unix :D and have been trying to configure an AIX server running 5.3. I used smitty or smit to configure interface 0 on the server. I am able to ping the IP I set, however I am still unable to ping the gateway. I configured the IP by navigating to Communications Applications... (6 Replies)
Discussion started by: cdub50
6 Replies
5. AIX
Just want to know if someone has a clue about what could be happening here:
I have an AIX box with four NICs in Ether channel connected to a Cisco Switch.
When I try to ping the default gateway, sometimes it works, but sometimes it doesn't work unless it has a defined static route.
Thanks... (1 Reply)
Discussion started by: witt
1 Replies
6. UNIX for Dummies Questions & Answers
I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a... (4 Replies)
Discussion started by: Rutgerncas
4 Replies
7. AIX
I just reinstalled a fresh install of 5300 07 on an old 44p model 170, after installing I set an IP Address on en2 and I tried to the ping default gateway, no response. I tried a
startsrc -g tcpip
... and then I can ping the default gateway. I broke the ping and tried again to ping. I cannot... (1 Reply)
Discussion started by: asyed123
1 Replies
8. Red Hat
Hi,
Here is the issue: There are 2 identical systems in the same subnet here. They can ping and ssh each other. One can ping the default gateway and one can not with error '... icmp_seq Destination Host Unreachable'. I can't find any difference between the two systems in terms of network... (4 Replies)
Discussion started by: aixlover
4 Replies
9. AIX
Hi,
I installed AIX 7.1 on a blade though (hmc with vio). I can ping the IP address, but not the gateway. Is there anything that I should configure?
Is there anything that I have to check with vio setting or Am I missing any configuration?
Please let me know further.
Thank you (5 Replies)
Discussion started by: pjeedu2247
5 Replies
10. UNIX for Advanced & Expert Users
I have setup a Linux machine on my server but for some reason Im unable to reach my default gateway. This is causing me to not communicate with the outside world (unable to connect to CentOS repos)
# ifconfig
enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet... (3 Replies)
Discussion started by: Junaid Subhani
3 Replies
LEARN ABOUT REDHAT
pvmfmstat
MSTAT(3PVM) PVM Version 3.4 MSTAT(3PVM)
NAME
pvm_mstat - Returns the status of a host in the virtual machine.
SYNOPSIS
C int mstat = pvm_mstat( char *host )
Fortran call pvmfmstat( host, mstat )
PARAMETERS
host Character string containing the host name.
mstat Integer returning machine status:
value MEANING
PvmOk host is OK
PvmNoHost host is not in virtual machine
PvmHostFail host is unreachable (and thus possibly failed)
DESCRIPTION
The routine pvm_mstat returns the status mstat of the computer named host with respect to running PVM processes. This routine can be used
to determine if a particular host has failed and if the virtual machine needs to be reconfigured. The function pvm_notify() can also be
used to notify the caller that a host has failed.
EXAMPLES
C:
mstat = pvm_mstat( "msr.ornl.gov" );
Fortran:
CALL PVMFMSTAT( 'msr.ornl.gov', MSTAT )
ERRORS
These error conditions can be returned by pvm_mstat
PvmSysErr
pvmd not responding.
PvmNoHost
giving a host name not in the virtual machine.
PvmHostFail
host is unreachable (and thus possibly failed).
SEE ALSO
pvm_notify(3PVM), pvm_config(3PVM)
30 August, 1993 MSTAT(3PVM)