Cannot ping gateway Post: 302424777

10 More Discussions You Might Find Interesting

1. IP Networking

Unable to ping the gateway IP itself

We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command 64 bytes from 124.168.215.40:...

2. IP Networking

Multihomed can not ping gateway

Hello this is my first post at this forum. Apologize for my lack of network understanding but Im posting to learn. I have a problem reaching default gateway 10.18.110.1 If I use my laptop I can ping 10.18.110.1 but with our red hat multihomed server the gateway does not respond to ping. cat...

3. Solaris

ping -s to default gateway very slow

I was install new solaris10 on m4000 model after that i "ping -s" to default gateway but it's take longtime (2 Min) to reply and if i use "ping" only it's reply to fase(2 sec). any body who can tell me about my problem and how to fix it please. i'm try to fix several days.

4. AIX

Can not Ping Gateway

Hello, I am new to Unix :D and have been trying to configure an AIX server running 5.3. I used smitty or smit to configure interface 0 on the server. I am able to ping the IP I set, however I am still unable to ping the gateway. I configured the IP by navigating to Communications Applications...

5. AIX

IBM Server doesn't ping gateway unless you put a static route

Just want to know if someone has a clue about what could be happening here: I have an AIX box with four NICs in Ether channel connected to a Cisco Switch. When I try to ping the default gateway, sometimes it works, but sometimes it doesn't work unless it has a defined static route. Thanks...

6. UNIX for Dummies Questions & Answers

Cannot ping default gateway

I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a...

7. AIX

Cant ping default gateway aix 53 07 new install

I just reinstalled a fresh install of 5300 07 on an old 44p model 170, after installing I set an IP Address on en2 and I tried to the ping default gateway, no response. I tried a startsrc -g tcpip ... and then I can ping the default gateway. I broke the ping and tried again to ping. I cannot...

8. Red Hat

Can not ping default gateway

Hi, Here is the issue: There are 2 identical systems in the same subnet here. They can ping and ssh each other. One can ping the default gateway and one can not with error '... icmp_seq Destination Host Unreachable'. I can't find any difference between the two systems in terms of network...

9. AIX

Networking Issue (Cant Ping the gateway)

Hi, I installed AIX 7.1 on a blade though (hmc with vio). I can ping the IP address, but not the gateway. Is there anything that I should configure? Is there anything that I have to check with vio setting or Am I missing any configuration? Please let me know further. Thank you

10. UNIX for Advanced & Expert Users

Unable to ping default gateway

I have setup a Linux machine on my server but for some reason Im unable to reach my default gateway. This is causing me to not communicate with the outside world (unable to connect to CentOS repos) # ifconfig enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet...

LEARN ABOUT DEBIAN

ifmetric

ifmetric(8)						      System Manager's Manual						       ifmetric(8)

NAME

       ifmetric - An IPv4 route metrics manipulation tool

SYNOPSIS

       ifmetric INTERFACE [METRIC]

DESCRIPTION

       ifmetric  is  a	Linux  tool  for setting the metrics of all IPv4 routes attached to a given network interface at once. This may be used to
       change the priority of routing IPv4 traffic over the interface. Lower metrics correlate with higher priorities.

       ifmetric uses the Linux NETLINK interface to manipulate the routes. Because of that it is compatible  with  routes  created  with  the  new
       iproute2 utility.

OPTIONS

       You  should specify the interface name as first parameter. The second parameter should be the new metric. If ommited the metric 0 (highest)
       is used.

RETURN VALUES

       0 Success

       1 Failure

AUTHOR

       ifmetric   was	written   by   Lennart	 Poettering   <mzvszrgevp   (at)    0pointer	(dot)	 de>.	 ifmetric    is    available	at
       http://0pointer.de/lennart/projects/ifmetric/

SEE ALSO

       route(8), ip(8) (iproute2)

COMMENTS

       This man page was written using xml2man(1) by Oliver Kurth.

Manuals 							       User							       ifmetric(8)

10 More Discussions You Might Find Interesting

1. IP Networking

Unable to ping the gateway IP itself

Discussion started by: chrisanto_2000

2. IP Networking

Multihomed can not ping gateway

Discussion started by: vettec3

3. Solaris

ping -s to default gateway very slow

Discussion started by: cesmk

4. AIX

Can not Ping Gateway

Discussion started by: cdub50