Sponsored Content
Operating Systems Solaris How to assign static ip address to the server having solaris 10. i.e. nge0 Post 302423910 by lufen on Sunday 23rd of May 2010 07:25:46 AM
Old 05-23-2010
How to assigne static ip to a interface that will sustain a boot:
Add host entry to /etc/hosts
add hostname to the file /etc/hostname.interface (hostname.nge0 for you) (you can also put in the ip here, if you dont want to add the host entry into /etc/hosts)
add netmask to /etc/netmasks
add defaultrouter ip in /etc/defaultrouter
init 6
ifconfig -a to check config is correct
netstat -rn to check defaultrouter is correct.

Just using ifconfig commands will not make the setting stay across reboots.
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

How to apply static ip address

Hi there, I have a Debian 5.0 server newly installed. By default, the ip address is given by dhcp. pegase:~# grep '^' /etc/network/interfaces auto lo iface lo inet loopback allow-hotplug eth0 iface eth0 inet dhcp pegase:~# head -2 /etc/hosts 127.0.0.1 localhost 127.0.1.1 ... (1 Reply)
Discussion started by: chebarbudo
1 Replies

2. Solaris

How to assign MAC address to N/W interface in solaris

I m having interface ce0 ce1 and its sub interfaces for that. I want to give MAC addresses for the same. How will I assign it. Please give solution for the same (4 Replies)
Discussion started by: sunray
4 Replies

3. Solaris

How to Configure a Static Ip Address

Hello friend, I am new in UNIX, but I want to learn a lot Well I have a problem to try to configure my PC with a static IP Address (IP 192.168.1.39, Mask 255.255.255.0, gateway 192.168.1.1) (DNS 200.48.225.130 and 200.48.225.146). where are the file that I must be change? The SO is Sun Solaris... (15 Replies)
Discussion started by: andresguillen
15 Replies

4. UNIX for Dummies Questions & Answers

Static IP address for solaris 10 virtual machine

Hi All I am having a solaris 10 virtual machine on vista (using vmware 7) laptop. Now i want to access virtual machine from vista using putty. Problem is that i insalled the solaris machine as dhcp. and whenever i connect to internet or reboot my system the IP address of solaris... (1 Reply)
Discussion started by: ankurk
1 Replies

5. Solaris

Solaris - Assign Static IP

Hi, I have cloned a SOLARIS 8 (BLADE 150) Hard Disk and have put into other system. So, now how do I configure the NIC and assign static IP for this new machine ? (8 Replies)
Discussion started by: angshuman_ag
8 Replies

6. Red Hat

Purpose of Static IP address through DHCP

Hi All, Could you please explain the purpose of assigning the static IP by using the DHCP Concept. Like by using the clients MAC address we assign the static IP Address. Waiting for your reply. Thanks in Advance. (6 Replies)
Discussion started by: Sharath Kumar
6 Replies

7. Solaris

How to resolve duplicated MAC address on Solaris server?

Hi folks, I found out the following: provadm@BKP_LIV_NPPGW_02:home/provadm%/usr/sbin/arp -a Net to Media Table: IPv4 Device IP Address Mask Flags Phys Addr ------ -------------------- --------------- -------- -------------------- ce5 BKP_OnM_NPPGW_02 255.255.255.255 SPLA 00:14:4f:44:e0:86... (1 Reply)
Discussion started by: kimurayuki
1 Replies

8. IP Networking

Free subdomain to my IP Address and Static IP

Hi all, I would need to register a random free subdomain address and associate that to my IP Address. Any suggestion of a good service? Also I don't have a static IP but i remember that there are services that automatically reset the right IP address behind the subdomain but i don't remember... (1 Reply)
Discussion started by: Tameto
1 Replies

9. IP Networking

Configuring static ip address on several systems

p { margin-bottom: 0.1in; line-height: 120%; }a:link { } Hello, I'm have an interesting issue with some Raspberry Pi's which I have on my home network. The pi's are on 192.168.1.102, 192.168.1.103, 192.168.1.104 Something very strange is happening on my network. The pi on 192.168.1.104 is... (2 Replies)
Discussion started by: JoeOnaMac
2 Replies

10. Linux

Unable to set static ip address

Hi All, Am using centos 7 in my vmware workstatio with the bridged network. when run the ifconfig cmd its not at all showing the ip address and pls advise how to set static ip address in my linux box. (1 Reply)
Discussion started by: sarathkumar s
1 Replies
defaultrouter(4)						   File Formats 						  defaultrouter(4)

NAME
defaultrouter - configuration file for default router(s) SYNOPSIS
/etc/defaultrouter DESCRIPTION
The /etc/defaultrouter file specifies a IPv4 host's default router(s). The format of the file is as follows: IP_address ... The /etc/defaultrouter file can contain the IP addresses or hostnames of one or more default routers, with each entry on its own line. If you use hostnames, each hostname must also be listed in the local /etc/hosts file, because no name services are running at the time that defaultrouter is read. Lines beginning with the ``#'' character are treated as comments. The default routes listed in this file replace those added by the kernel during diskless booting. An empty /etc/defaultrouter file will cause the default route added by the kernel to be deleted. Use of a default route, whether received from a DHCP server or from /etc/defaultrouter, prevents a machine from acting as an IPv4 router. You can use routeadm(1M) to override this behavior. FILES
/etc/defaultrouter Configuration file containing the hostnames or IP addresses of one or more default routers. SEE ALSO
in.rdisc(1M), in.routed(1M), routeadm(1M), hosts(4) SunOS 5.10 17 Aug 2004 defaultrouter(4)
All times are GMT -4. The time now is 02:47 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy