05-23-2010
How to assigne static ip to a interface that will sustain a boot:
Add host entry to /etc/hosts
add hostname to the file /etc/hostname.interface (hostname.nge0 for you) (you can also put in the ip here, if you dont want to add the host entry into /etc/hosts)
add netmask to /etc/netmasks
add defaultrouter ip in /etc/defaultrouter
init 6
ifconfig -a to check config is correct
netstat -rn to check defaultrouter is correct.
Just using ifconfig commands will not make the setting stay across reboots.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi there,
I have a Debian 5.0 server newly installed.
By default, the ip address is given by dhcp.
pegase:~# grep '^' /etc/network/interfaces
auto lo
iface lo inet loopback
allow-hotplug eth0
iface eth0 inet dhcp
pegase:~# head -2 /etc/hosts
127.0.0.1 localhost
127.0.1.1 ... (1 Reply)
Discussion started by: chebarbudo
1 Replies
2. Solaris
I m having interface ce0 ce1 and its sub interfaces for that.
I want to give MAC addresses for the same.
How will I assign it.
Please give solution for the same (4 Replies)
Discussion started by: sunray
4 Replies
3. Solaris
Hello friend, I am new in UNIX, but I want to learn a lot
Well I have a problem to try to configure my PC with a static IP Address
(IP 192.168.1.39, Mask 255.255.255.0, gateway 192.168.1.1)
(DNS 200.48.225.130 and 200.48.225.146).
where are the file that I must be change?
The SO is Sun Solaris... (15 Replies)
Discussion started by: andresguillen
15 Replies
4. UNIX for Dummies Questions & Answers
Hi All
I am having a solaris 10 virtual machine on vista (using vmware 7) laptop.
Now i want to access virtual machine from vista using putty.
Problem is that i insalled the solaris machine as dhcp. and whenever i connect to internet or reboot my system the IP address of solaris... (1 Reply)
Discussion started by: ankurk
1 Replies
5. Solaris
Hi,
I have cloned a SOLARIS 8 (BLADE 150) Hard Disk and have put into other system. So, now how do I configure the NIC and assign static IP for this new machine ? (8 Replies)
Discussion started by: angshuman_ag
8 Replies
6. Red Hat
Hi All,
Could you please explain the purpose of assigning the static IP by using the DHCP Concept. Like by using the clients MAC address we assign the static IP Address. Waiting for your reply. Thanks in Advance. (6 Replies)
Discussion started by: Sharath Kumar
6 Replies
7. Solaris
Hi folks,
I found out the following:
provadm@BKP_LIV_NPPGW_02:home/provadm%/usr/sbin/arp -a
Net to Media Table: IPv4
Device IP Address Mask Flags Phys Addr
------ -------------------- --------------- -------- --------------------
ce5 BKP_OnM_NPPGW_02 255.255.255.255 SPLA 00:14:4f:44:e0:86... (1 Reply)
Discussion started by: kimurayuki
1 Replies
8. IP Networking
Hi all,
I would need to register a random free subdomain address and associate that to my IP Address. Any suggestion of a good service?
Also I don't have a static IP but i remember that there are services that automatically reset the right IP address behind the subdomain but i don't remember... (1 Reply)
Discussion started by: Tameto
1 Replies
9. IP Networking
p { margin-bottom: 0.1in; line-height: 120%; }a:link { } Hello,
I'm have an interesting issue with some Raspberry Pi's which I have on my home network.
The pi's are on 192.168.1.102, 192.168.1.103, 192.168.1.104
Something very strange is happening on my network. The pi on 192.168.1.104 is... (2 Replies)
Discussion started by: JoeOnaMac
2 Replies
10. Linux
Hi All,
Am using centos 7 in my vmware workstatio with the bridged network. when run the ifconfig cmd its not at all showing the ip address and pls advise how to set static ip address in my linux box. (1 Reply)
Discussion started by: sarathkumar s
1 Replies
LEARN ABOUT OSF1
install-solaris
install-solaris(1M) install-solaris(1M)
NAME
install-solaris - install the Solaris operating system
SYNOPSIS
install-solaris
install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation,
install-solaris invokes either a text-based installer or a graphical installer.
The following minimum requirements for physical memory dictate which features are available during installation:
For SPARC machines:
128 MB
Minimum physical memory for all installation types
128 MB
Minimum physical memory required for windowing system
384 MB
Minimum physical memory required for graphical-based installation
For x86 machines:
256 MB
Minimum physical memory for all installation types
256 MB
Minimum physical memory required for windowing system
512 MB
Minimum physical memory required for graphical-based installation
In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea-
tures available.
install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more
details.
install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
installation media. Refer to the for disk space requirements.
Refer to the for more information on the various menus and selections.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcdrom (Solaris instal- |
| |lation media) |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
pkginfo(1), install(1M), pkgadd(1M), attributes(5)
It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.
23 Sep 2005 install-solaris(1M)