Note 1: If you have the frame buffer Raptor GFXP -04 REV 50
(part 370-3753-04), you *must* install patch 110126-03 to upgrade the
FCode in the card **BEFORE** you can do the firmware update. Revisions -05 and up of the frame buffer are not affected.
Failure to install the frame buffer patch (110126-03) will cause
"FATAL" resets after the firmware update.
I know I have a Raptor PGX32 frame buffer, is there a way to know what version of the frame buffer FCode I have? Do I need to apply the moentioned patch?
hi,
i hv received SUNfire 280R system ........for its initial configuration i want to connect to it through hyperterminal from the windows system..........i hv got one serial port to RJ-45 port converter with the system............can anybody tell me the normal console cable which is used to... (3 Replies)
Greetings all,
I'm in a bit of a situation. I have this Sunfire 280R system that did not have a floppy drive in it, yet we needed one. We grabbed one from another Sun box we had laying around unused, and installed it. The system couldnt recognize it. Tried another floppy drive (non-sun) and... (4 Replies)
Hi there
Does anybody know what the biggest capacity disk I can get into a Sunfire 280R
I currently have two 73gb disks , but I need to get these up to the biggest available
Any help would be greatly appreciated (4 Replies)
Hi,
We had a disk go bad in this SunFire 280R, running Solaris 8 - Generic_117350-46. We replaced the disk and partitioned it. We metadetached all the metadevices but for some reason the new disk is showing up in the metadb as Concat/Stripe and it won't let us re-sync the mirror. We are not... (2 Replies)
Hi,
I have to question:
1) when O/S is booting, i see messages:
/dev/rdsk/c1t0d0s5: is logging
/dev/rdsk/c1t0d0s3: is logging
/dev/rdsk/c1t0d0s7: is logging
i partitioned these slices during installation of O/S 5.9. I can access to these mountpoint no problem. But... (3 Replies)
hi,
i just completed installing O/S 5.9 on Sunfire 280R with O/S 5.9. During installation, i wasn't able to add IP, Default gateway, NDS and netmask because the lan port wasn't not active yet. Now that i have a lan port active, how to add network components onto the system?
I did ifconfig to... (1 Reply)
Hi,
i just finished installing solaris 5.9 and I'm looking for the tools to tell me if i should update the patches or how to make sure that the current patches are ok?
thanks (2 Replies)
Hi,
I' trying to install O/S 5.9 on Sparc system Sunfire 280R. I downloaded CD install and CD 2 from Sun Website but later i dowloaded CD 2 that i forgot for my installation. All CD are in ISO formats.
I boot system at OK prompt then issue
OK boot cdrom
when it asks for CD 1, i removed... (7 Replies)
I got the system couple of days back from one of my friend. Last night I turned it on and I noticed that maintenance LED is on. At the same time I added an LCD monitor via VGA and nothing was showing on the screen. Though the system does not have any HDD So not sure if system will even show a BIOS... (3 Replies)
Discussion started by: pgirish007
3 Replies
LEARN ABOUT NETBSD
hme
HME(4) BSD Kernel Interfaces Manual HME(4)NAME
hme -- Sun Microelectronics STP2002-STQ Ethernet interfaces device driver
SYNOPSIS
hme* at pci? dev ? function ?
hme* at sbus? slot ? offset ?
DESCRIPTION
The hme driver supports Sun Microelectronics STP2002-STQ Fast Ethernet interfaces.
HARDWARE
The hme driver supports the on-board Ethernet interfaces of many Sun UltraSPARC workstation and server models.
Cards supported by the hme driver include:
Sun PCI SunSwift Adapter (``SUNW,hme'')
Sun SBus SunSwift Adapter (``hme'' and ``SUNW,hme'')
Sun PCI Sun100BaseT Adapter 2.0 (``SUNW,hme'')
Sun SBus Sun100BaseT 2.0 (``SUNW,hme'')
Sun PCI Quad FastEthernet Controller (``SUNW,qfe'')
Sun SBus Quad FastEthernet Controller (``SUNW,qfe'')
The STP2002 family supports hardware checksumming to assist in computing IPv4 TCP/UDP checksums. The hme driver supports this feature of the
chip. See ifconfig(8) for information on how to enable this feature.
SEE ALSO ifmedia(4), intro(4), mii(4), ukphy(4), ifconfig(8)
Sun Microelectronics, STP2002QFP Fast Ethernet, Parallel Port, SCSI (FEPS) User's Guide,
http://mediacast.sun.com/users/Barton808/media/STP2002QFP-FEPs_UG.pdf, April 1996.
HISTORY
The hme driver first appeared in NetBSD 1.5.
AUTHORS
The hme driver was written by Paul Kranenburg <pk@NetBSD.org>.
BUGS
Connecting a MII transceiver on those cards that support it will cause the RJ45 connector to be detected as PHY instance 1, instead of the
default instance 0.
BSD June 23, 2012 BSD
05-07-2010
