04-22-2010
You need to use mkisofs first as shown in you other thread.
10 More Discussions You Might Find Interesting
1. IP Networking
I am running RH7.3 on a compaq presario box. The network card is a Linksys one. I am only able to communicate with the local network (only the local IPs are accessible). When I try to ping another box I get a "Connect: Network is unreachable" message. What could be the problem.
Thanks in... (2 Replies)
Discussion started by: skotapal
2 Replies
2. Cybersecurity
I have inherited a Sun Ultra-1, running sunOS 5.8
While on this machine, I cannot ping www.yahoo.com
I cannot ping this machine from withing our lan.
I do not have an static IP for this machine and used
Iconfig hme0 auto-dhcp start.
All is well,
It seems to me that the previous owner,... (1 Reply)
Discussion started by: defense
1 Replies
3. UNIX for Dummies Questions & Answers
Is it possible for a group of servers to monitor each other and then send an alert if one of them is no longer 'alive'?
Or if its easier have one server that monitors the other five and then sends an alert.
If so how would this be done?
Thanks (3 Replies)
Discussion started by: Sepia
3 Replies
4. Linux
All,
I have to servers (NT and REL4).
We can access the application on NT from Linux but we cannot access the applications on Linux when accessed from NT.
The applicaiton is running on Linux with some IP:Port. When we try to access that application from NT, it says that the port is... (1 Reply)
Discussion started by: The One
1 Replies
5. Solaris
Hi all,
I cannot reach my SERVER from my NetBackup server connect through SERVER_prv ("cannot connect to client")
My SERVER was Sun OS 5.8, below is the message i get when i ping my SERVER:
# ping 192.168.X.X or
# ping SERVER_prv
ICMP Net Unreachable from gateway 172.16.102.XXX
for... (3 Replies)
Discussion started by: beginningDBA
3 Replies
6. Post Here to Contact Site Administrators and Moderators
Apparently (at least) 2 of the servers responsible for serving the static images and the JavaScript are down or otherwise unreachable. Affected are www.unix.com and www.unix.com, while www.unix.com is still up. A check on this website confirmed it. Checked as of 2010-06-16 08:11 UTC. (13 Replies)
Discussion started by: pludi
13 Replies
7. Solaris
Hey Guys:
I am trying to add a route for assign a network interface to the traffic to/from a specific net, but allways to get the same system message : network is unreacheable
root@ColectorDMSCNT # route add net 200.44.46.0/24 161.196.84.196 1
add net 200.44.46.0/24: gateway... (2 Replies)
Discussion started by: aggadtech08
2 Replies
8. UNIX for Dummies Questions & Answers
Hello,
I'm using Ubuntu, and when I check "/"(root directory)'s properties. The window says "some contents unreachable". What is the "some contents"?
http://i.imgur.com/UWn8Q.png (2 Replies)
Discussion started by: hz_i3
2 Replies
9. UNIX for Advanced & Expert Users
Hi, all:
How can I check what happen with my own NIC driver which response "successful" when local PC "ping" a remote linux PC but "unreachable" when it "ping" a remote windows XP PC? My writed driver runs in linux 3.0.4 kernel.
thanks!
li, kunlun (1 Reply)
Discussion started by: liklstar
1 Replies
10. Solaris
Seems to wanboot ok but then fails to connect to server. What do I need to check?
{0} ok boot net - install
Boot device: /pci@300/pci@1/pci@0/pci@1/network@0 File and args: - install
1G link up
<time unavailable> wanboot info: WAN boot messages->console
<time unavailable>... (2 Replies)
Discussion started by: psychocandy
2 Replies
IPKDB(4) BSD Kernel Interfaces Manual IPKDB(4)
NAME
ipkdb -- IP-based kernel debugger
SYNOPSIS
options IPKDB
options IPKDBSECURE
options IPKDBKEY=""IPKDB key for remote debugging""
options IPKDB_NE_PCISLOT=x
DESCRIPTION
ipkdb is a kernel debugger that uses UDP and IP to communicate with a remote debugger (normally gdb(1)).
Since the debugger uses its own driver to talk to the networking hardware, the number of supported network interfaces is a lot less than what
is supported by the kernel. At the time of this writing, there is only support for a NE2000 compatible card in a PCI slot. In order for
ipkdb to find your card, you need to specify the slot the card is in via the options IPKDB_NE_PCISLOT.
To use ipkdb, you have to set up a DHCP server, from which ipkdb can get the IP address for the interface that is used for debugging.
To enter ipkdb, the remote debugger has to send the protocol start packet. E.g., gdb will do this on the command
target ipkdb debuggee IPKDB key for remote debugging
where debuggee is the name of the machine to debug (which must resolve to the IP address of the interface), and the rest of the line corre-
sponds to the definition of IPKDBKEY (see below). For ipkdb to actually see this packet, the interface which is used for debugging has to be
set up to actually receive packets, i.e. it has to be up and running.
To prevent messing around with a secured system, ipkdb normally also checks the security level at which the kernel is running. ipkdb will
only work with security levels less than 1, unless the kernel is configured with options IPKDBSECURE.
In addition, the debugger is forcedly entered on a panic, as well as on initial startup, if you boot the kernel with the -d option (note that
this however is machine dependent). On such a forced enter to ipkdb there is no need for the interface in question to already be up and run-
ning, since ipkdb only needs to send/receive packets via its own driver.
As some form of security against the occasional hacker, ipkdb uses the definition of options IPKDBKEY to compute a checksum on the data in
every packet. The remote debugger has to send this checksum, based on the data it sends and the key, or ipkdb ignores the packet. This is
also used in order to check against data errors on the connection.
SEE ALSO
gdb(1), ddb(4), ip(4), udp(4), init(8)
HISTORY
ipkdb appeared in NetBSD 1.3 for the first time. Its configuration and setup changed quite a bit in NetBSD 1.5.
BUGS
Since the kernel includes the definition of IPKDBKEY, anyone who can read the kernel can extract it and use it to enter ipkdb.
There is no support for ip6(4).
BSD
March 27, 2000 BSD