04-22-2010
Please plug and unplug again your DIMM.
Quote:
Originally Posted by
Caully
Hi All,
I recently had issues with my new T2000 server. I purchased a new mainboard and swapped the CPU and DIMMs to the new board. Now when i power on the server im unable to do so. I get the following error:
‘SC Alert: Host system poweron failed due to fault at MB/FF_POK.'
When i do showfault in sc i get the following:
ph2-sc> showfaults
ID FRU Fault
1 MB Host system poweron failed due to fault at MB/FF_POK.
Anyone have any idea how to resolve this issue???
Thanks.
10 More Discussions You Might Find Interesting
1. Solaris
I have one Sun Netra T2000 Server. The ALOM SC admin password of this server is not known. Could you anyone help and tell me how can i reset the SC admin account password??
Thanks in advance.. (2 Replies)
Discussion started by: sudhir_shet
2 Replies
2. Solaris
Hi, i am really 'fresh' to Solaris or any UNIX OS. My role as web developer but i need slightly involve to Solaris support. It is harder for me to understand it and i recently encounter a problems.
/var file system (/dev/md/rdsk/d425) is being checked.
run fsck -F ufs /dev/md/rdsk/d425
... (8 Replies)
Discussion started by: webster5u
8 Replies
3. Solaris
Hi
I am fresher in Virtualisation in solaris 10.I need to know how to install and configure guest OS, I have a server Sun T2000 with solaris 10 OS BASE.
How to install logical domain, what are the prerequest for installing l domain
can some one guide me what are the basic requirement to... (2 Replies)
Discussion started by: solaris8in
2 Replies
4. Infrastructure Monitoring
dears, any one knows how to use linux command to monitor hp server Redhat dual power status? any 1 of power failure then alarm will triggered. (4 Replies)
Discussion started by: maxlee24
4 Replies
5. Hardware
Hi All
I have a Sun T2000 server. Couple of years ago I had configured and mirrored the boot drive with an other drive using hardware RAID 1 using raidctl command.
Following is the hardware RAID output.
root@oracledatabaseserver / $ raidctl
RAID Volume RAID RAID Disk... (0 Replies)
Discussion started by: Tirmazi
0 Replies
6. UNIX for Advanced & Expert Users
i have doubt about how to power on server from remote location with out contacting with data center people? please anybody replay with whole info.
thank you. (3 Replies)
Discussion started by: bhaskerreddy.ch
3 Replies
7. Solaris
SPARC Enterprise T5440 Server, can not power off
I connect to Service Processor via serial port and submit the following to boot the system, it boots fine but can not power off the system. Can someone help?
The following takes me to unix login
-> start /SYS
-> start /SP/console... (6 Replies)
Discussion started by: paulk93
6 Replies
8. Solaris
==============================
ALOM BOOTMON v1.3.1
ALOM Build Release: 001
Reset register: f0000000 EHRS ESRS LLRS SWRS
ALOM POST 1.0
Dual Port Memory Test, PASSED.
TTY External - Internal Loopback Test
TTY External - Internal Loopback Test, PASSED.
TTYC - Internal Loopback Test
TTYC -... (4 Replies)
Discussion started by: Sameer Naik
4 Replies
9. Linux
Can anyone tell me how to start pc automatically when power comes,
here I just want to start server automatically, on boot, my server starts automatically because I have written some startup commands in rc.local file but if power fails, then how can I boot automatically (2 Replies)
Discussion started by: Akshay Hegde
2 Replies
10. Solaris
I have a T2000 enterprise SPARC server that's no longer on contract with Oracle. It's on old firmware (6.3.x). After a power-down this weekend, it won't boot normally. Boot snapshot at the bottom of the post.
It can boot to cdrom, and it'll boot to failsafe mode, but it won't do a regular... (9 Replies)
Discussion started by: val riverwalk
9 Replies
power(9E) Driver Entry Points power(9E)
NAME
power - power a device attached to the system
SYNOPSIS
#include <sys/ddi.h>
#include <sys/sunddi.h>
int prefixpower(dev_info_t *dip, int component, int level);
INTERFACE LEVEL
Solaris DDI specific (Solaris DDI). This entry point is required. If the driver writer does not supply this entry point, the value NULL
must be used in the cb_ops(9S) structure instead.
PARAMETERS
dip Pointer to the device's dev_info structure.
component Component of the driver to be managed.
level Desired component power level.
DESCRIPTION
The power(9E) function is the device-specific Power Management entry point. This function is called when the system wants the driver to set
the power level of component to level.
The level argument is the driver-defined power level to which the component needs to be set. Except for power level 0, which is inter-
preted by the framework to mean "powered off," the interpretation of level is entirely up to the driver.
The component argument is the component of the device to be power-managed. The interpretation of component is entirely up to the driver.
When a requested power transition would cause the device to lose state, the driver must save the state of the device in memory. When a
requested power transition requires state to be restored, the driver must restore that state.
If a requested power transition for one component requires another component to change power state before it can be completed, the driver
must call pm_raise_power(9F) to get the other component changed, and the power(9E) entry point must support being re-entered.
If the system requests an inappropriate power transition for the device (for example, a request to power down a device which has just
become busy), then the power level should not be changed and power should return DDI_FAILURE.
RETURN VALUES
The power() function returns:
DDI_SUCCESS Successfully set the power to the requested level.
DDI_FAILURE Failed to set the power to the requested level.
CONTEXT
The power() function is called from user or kernel context only.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Interface stability |Evolving |
+-----------------------------+-----------------------------+
SEE ALSO
attach(9E), detach(9E), pm_busy_component(9F), pm_idle_component(9F), pm_raise_power(9F), cb_ops(9S)
Writing Device Drivers
Using Power Management
SunOS 5.10 12 Dec 2003 power(9E)