1) solaris 10 should work to a significant amount on all generic platforms
2) fire up:
in any case, try to see smth going on with dmesg while trying to get your USB drive plugged in.
Hi guys,
Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot).
I did boot -s and checked using ifconfig -a command but i got the same... (0 Replies)
Hi-
I would like to know if anyone has used any USB External Hard Drive, about 500/750GB or 1TB, with any of the Solaris 10 "SPARC" systems. Not on intel nor amd platform.
I'm looking for the compatible drive and found a few listed on Sun solaris ready page, but I'd like to have inputs from... (3 Replies)
I have a T2000 server running solaris 10, it has 4 USB ports. I want to extend the storage capacity by attaching an external USB drive and mounting it as an other mount point.
How do I do that, the following link gives information about USB in Solaris OS, ... (1 Reply)
Hi,
/sbin/ifconfig -a
when i login as guest user , output like below,
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
eri0: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 1500 index 2
inet... (5 Replies)
Dear friends,
I have the DVD image of solaris 10 but I don't have DVD writer to burn it onto a dvd R. I was wondering if I could install Solaris from my 4gb usb flash drive as my PC supports booting from usb. I have installed Windows 7 this way recently, I have no idea about Solaris. Could you... (2 Replies)
Hi,
I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface.
Please advise how to configure network interfaces using VMware. (1 Reply)
Dear All,
I have a solaris Server in which I have 4 network interfaces , out of which only one is used . So all the applications are using this interface .
The interface speed is 1000Mbps . I find no hardware issue or packets g being dropped.
But i find that no of Input and Output... (4 Replies)
Got a T2000 which has got the 2.5" SAS drives. Want to be able, if I can, to connect to USB caddy and connect to a V440.
Anyone ever tried this? To be honest, having problems even finding a SAS-USB caddy. (0 Replies)
Discussion started by: psychocandy
0 Replies
LEARN ABOUT SUNOS
sppptun
sppptun(1M) System Administration Commands sppptun(1M)NAME
sppptun - PPP tunneling driver utility
SYNOPSIS
sppptun plumb
sppptun plumb protocol device
sppptun unplumb interface
sppptun query
DESCRIPTION
The sppptun utility is used to configure and query the Solaris PPP tunneling device driver, /dev/sppptun. Currently, only PPP over Ether-
net (PPPoE) is supported, so the plumb and unplumb arguments are used to specify Ethernet interfaces that are to be used for PPPoE, and the
query option lists the plumbed interfaces.
The use of sppptun to add interfaces is similar to the use of ifconfig(1M) to add interfaces to IP. The plumbing is done once for each
interface, preferably at system start-up time, and is not normally manipulated on a running system. If multiple instances of PPP are run
over a single interface, they share the plumbing to that interface. Plumbing for each session is not required (and not possible for PPPoE).
The proper way to plumb interfaces for PPPoE is to list the interfaces, one per line, in the /etc/ppp/pppoe.if file.
USAGE
sppptun plumb
When specified with no additional arguments, the plumb argument lists the protocols that are supported by the utility. These are the
strings that are used as the protocol argument below.
sppptun plumb protocol device
This plumbs a new interface into the driver. The protocol parameter is pppoe for the PPP-carrying "Session Stage" connection or pppoed
for the PPPoE "Discovery Stage" connection. Both connections must be present for each Ethernet interface that is to be used for PPPoE.
The device parameter is the path name of the Ethernet interface to use (use ifconfig(1M) to list available devices). If the path begins
with /dev/, then this portion may be omitted.
sppptun unplumb interface
This removes an existing interface from the driver and terminates any PPP sessions that were using the interface. The interface parame-
ter is the name of the interface as reported when the interface was plumbed.
sppptun query
Displays the canonical names of all interfaces plumbed into the /dev/sppptun device driver.
EXAMPLES
Example 1: Setting up to Use PPPoE on hme0
Plumb the hme0 interface.
# sppptun plumb pppoed hme0
hme0:pppoed
# sppptun plumb pppoe hme0
hme0:pppoe
Remove the hme0 interface.
# sppptun unplumb hme0:pppoed
# sppptun unplumb hme0:pppoe
Example 2: Script to Remove All Plumbed Interfaces
#!/bin/sh
for intf in `sppptun query`
do
sppptun unplumb $intf
done
EXIT STATUS
The following exit values are returned:
0 Successful completion.
1 One or more errors occurred.
FILES
/etc/ppp/pppoe.if list of Ethernet interfaces to be plumbed at boot time
/usr/sbin/sppptun executable command
/dev/sppptun Solaris PPP tunneling device driver
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWpppdt |
+-----------------------------+-----------------------------+
SEE ALSO pppd(1M), pppoec(1M), pppoed(1M), sppptun(7M)
RFC 2516, Method for Transmitting PPP Over Ethernet (PPPoE), Mamakos et al, February 1999
SunOS 5.10 19 Mar 2001 sppptun(1M)