04-13-2010
you have to post the whole configuration... there are problems with you filesystems.
10 More Discussions You Might Find Interesting
1. Solaris
Hi,
After I installed Solaris 10 in the Intel platform (chipset 865*) network card was not detected, were shall I get this driver? iam new to Solaris. (2 Replies)
Discussion started by: pravin_2929
2 Replies
2. Solaris
I am seeking help from the gurus in this forum and hope that I can find answers soon. Anyone who provide the answers will be greatly appreciated.
I have a sparc box with Solaris 10 on it. We install Solaris with zone structure. One global zone and two other zone. I installed Oracle DB on global... (6 Replies)
Discussion started by: duke0001
6 Replies
3. Solaris
I have the following situation
1) Start JBoss Server 1
2) Within application - print as normal
3) Start JBoss Server 2
4) Printing STOPS on Server 1; Printing does NOT WORK on Server 2
Only solution is to stop Server 2;
Restart Server 1
Then Printing works as normal.
Doung a truss... (8 Replies)
Discussion started by: pmm
8 Replies
4. Solaris
I am trying to create a branded 10 zone on a Solaris 11.1 control domain. I am using a flar image (cpio) from an existing LDOM. Here are the steps taken after flarcreate.
#zonecfg -z <device>
>create -b
>set brand=solaris10
>set zonepath=/zonez/<device>
>set ip-type=exclusive
>add net... (1 Reply)
Discussion started by: aeroforce
1 Replies
5. Solaris
Hello, I followed these instructions to create a Solaris 11 zone:
http://www.oracle.com/technetwork/articles/servers-storage-admin/o11-092-s11-zones-intro-524494.html
And I am unable to ping anything from the Local Zone except for the IP address of the global zone.
My global zone has an IP... (6 Replies)
Discussion started by: unblockable
6 Replies
6. Solaris
I am trying to install a zone on Solaris 11.
I am following the instructions for zones intro at oracle.com (I can't post the url yet.)
I get up to Listing 2 when the error occurs.
# zoneadm -z testzone install
The following ZFS file system(s) have been created:
... (7 Replies)
Discussion started by: Kinesia
7 Replies
7. Solaris
Have 2 nics on physical system
net0 phys 1500 up --
net1 phys 1500 up --
1. I want to create a link aggregation with LACP enabled with above 2 nics
2. Create port-group(Like we create on ESXi) with VLAN-ID 2141
3. And assign this... (0 Replies)
Discussion started by: Shirishlnx
0 Replies
8. Solaris
I want to migrate a solaris 10 os to solaris 11.4 zone.
I did this
a)Collect some data like id sysid,disks,ip,etc..on solaris10
OK
b)Create this file.cfg with this command on solaris 10
zonep2vchk -c > /migration/sol10.cfg
OK
c)Create the archive flash on Solaris10 (1 Reply)
Discussion started by: Linusolaradm1
1 Replies
9. Solaris
Hi,
I have a Solaris 10 zone which I need to configure on a new network. I have configured the new IP on the zone itself and I can ping the interface from a node on the same network, but not from another network. Basically I need to know how to route the traffic from the zone to it's... (3 Replies)
Discussion started by: sparcman
3 Replies
10. Solaris
Hi, hoping someone can help, its been a while since I used Solaris.
After creating a NGZ (non global zone), the NGZ can access the GZ (Global Zone) and the GZ can access the NGZ (using ssh, zlogin)
However, the NGZ cannot access any other netwqork devices, it can't even see the default router
... (2 Replies)
Discussion started by: GazinLincoln
2 Replies
LEARN ABOUT SUNOS
install-solaris
install-solaris(1M) install-solaris(1M)
NAME
install-solaris - install the Solaris operating system
SYNOPSIS
install-solaris
install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation,
install-solaris invokes either a text-based installer or a graphical installer.
The following minimum requirements for physical memory dictate which features are available during installation:
For SPARC machines:
128 MB
Minimum physical memory for all installation types
128 MB
Minimum physical memory required for windowing system
384 MB
Minimum physical memory required for graphical-based installation
For x86 machines:
256 MB
Minimum physical memory for all installation types
256 MB
Minimum physical memory required for windowing system
512 MB
Minimum physical memory required for graphical-based installation
In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea-
tures available.
install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more
details.
install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
installation media. Refer to the for disk space requirements.
Refer to the for more information on the various menus and selections.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcdrom (Solaris instal- |
| |lation media) |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
pkginfo(1), install(1M), pkgadd(1M), attributes(5)
It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.
23 Sep 2005 install-solaris(1M)