04-08-2010
Haven't done it myself, but look into '--bind-address=ADDRESS' option
10 More Discussions You Might Find Interesting
1. Solaris
Yes. But just wait a bit. How to do it via system calls? I'm just a newbie in Unix\Linux\Solaris e.t.c. programming. Can anyone help me? I need an advice probably how to do it or may be what API to read... :) Please, help... (2 Replies)
Discussion started by: LocalStorm
2 Replies
2. IP Networking
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
3. SCO
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
4. AIX
Hi all, this is my first post on this forum. My main problem is this:
I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (0 Replies)
Discussion started by: snakernetb
0 Replies
5. AIX
Hi all, this is my first post on this forum. My main problem is this:
I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (1 Reply)
Discussion started by: snakernetb
1 Replies
6. Solaris
I got second IOU in my M5000 but not able bring internal network interfcae .. ike i don't get link on those 2 interfaces .. and the same network cable plugged in PCI network card it works like a charm Is there any special way to enable the internal IOU interfaces or i have bad nics ? (8 Replies)
Discussion started by: fugitive
8 Replies
7. Debian
Hello
i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address
then i save it wq!
then i restart the networking , /etc/init.d/networking restart .
but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Discussion started by: learn82
5 Replies
8. UNIX for Advanced & Expert Users
All, I have a quad NIC on a V880 running Solaris 9. I've heard you can bond interfaces together and get better throughput. I found this link that seems to describe the process well. However, the command mentioned (dladm) is missing. Is there some package I need to install to get this command? Thx.... (2 Replies)
Discussion started by: agcodba
2 Replies
9. UNIX for Dummies Questions & Answers
i need a one liner command that writes in /var/log/net.log the date when i connect to the network and when i disconect ..i know that i need to write somethin in /etc/network/interfaces but idk what ! please help (1 Reply)
Discussion started by: g0dlik3
1 Replies
10. Linux
I just ran sudo service networking start on Ubuntu 16.00 and came out with error message
Job for networking service failed because control process exited with error code see systemctl status networking.service
I tried to also run this command
systemctl status networking.service
I also got an... (4 Replies)
Discussion started by: DOkuwa
4 Replies
LEARN ABOUT MOJAVE
curlopt_resolve
CURLOPT_RESOLVE(3) curl_easy_setopt options CURLOPT_RESOLVE(3)
NAME
CURLOPT_RESOLVE - provide custom host name to IP address resolves
SYNOPSIS
#include <curl/curl.h>
CURLcode curl_easy_setopt(CURL *handle, CURLOPT_RESOLVE,
struct curl_slist *hosts);
DESCRIPTION
Pass a pointer to a linked list of strings with host name resolve information to use for requests with this handle. The linked list should
be a fully valid list of struct curl_slist structs properly filled in. Use curl_slist_append(3) to create the list and
curl_slist_free_all(3) to clean up an entire list.
Each single name resolve string should be written using the format HOST:PORT:ADDRESS where HOST is the name libcurl will try to resolve,
PORT is the port number of the service where libcurl wants to connect to the HOST and ADDRESS is the numerical IP address. If libcurl is
built to support IPv6, ADDRESS can of course be either IPv4 or IPv6 style addressing.
This option effectively pre-populates the DNS cache with entries for the host+port pair so redirects and everything that operations against
the HOST+PORT will instead use your provided ADDRESS. Addresses set with CURLOPT_RESOLVE(3) will not time-out from the DNS cache like ordi-
nary entries.
The provided ADDRESS set by this option will be used even if CURLOPT_IPRESOLVE(3) is set to make libcurl use another IP version.
Remove names from the DNS cache again, to stop providing these fake resolves, by including a string in the linked list that uses the format
"-HOST:PORT". The host name must be prefixed with a dash, and the host name and port number must exactly match what was already added pre-
viously.
DEFAULT
NULL
PROTOCOLS
All
EXAMPLE
CURL *curl;
struct curl_slist *host = NULL;
host = curl_slist_append(NULL, "example.com:80:127.0.0.1");
curl = curl_easy_init();
if(curl) {
curl_easy_setopt(curl, CURLOPT_RESOLVE, host);
curl_easy_setopt(curl, CURLOPT_URL, "http://example.com");
curl_easy_perform(curl);
/* always cleanup */
curl_easy_cleanup(curl);
}
curl_slist_free_all(host);
AVAILABILITY
Added in 7.21.3. Removal support added in 7.42.0.
RETURN VALUE
Returns CURLE_OK if the option is supported, and CURLE_UNKNOWN_OPTION if not.
SEE ALSO
CURLOPT_IPRESOLVE(3), CURLOPT_DNS_CACHE_TIMEOUT(3), CURLOPT_CONNECT_TO(3),
libcurl 7.54.0 May 17, 2016 CURLOPT_RESOLVE(3)