Sponsored Content
Full Discussion: Unix Network Routes
Special Forums IP Networking Unix Network Routes Post 302407739 by erice on Friday 26th of March 2010 09:03:23 AM
Old 03-26-2010
Can you post the output of netstat -nr, and netstat -in from the HPUX system?
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

How to add 2 gateway routes?

I need some help adding routes in sco. I am using SCO Openserver 5.0.4. Basically I have 2 gateways here. The first is 10.15.1.1 and allows me access to the rest of the computers in the office and in other offices. The other gateway is 10.15.10.2 and is the sonicwall that will allow access... (3 Replies)
Discussion started by: cstovall
3 Replies

2. Debian

Setting Routes and such

Ok, I made changes to my routing tables..... which file do I modify to make the routes initialize correctly when the machine boots up? I work with all flavours of Unix/Linux... but this is an older box... Linux, Release 2.2.14-5.0. I did a grep for the default route in /etc, but didnt find... (2 Replies)
Discussion started by: djsal
2 Replies

3. Solaris

Where are routes stored ?

Hi there When adding a route (or indeed deleting a route) which file is amended ? I am moving a box from one network to another and when it starts up it tries to connect run 'add net 192.x.x.x' etc etc ...but i dont want it to do that where do I edit these route additions cheers (5 Replies)
Discussion started by: hcclnoodles
5 Replies

4. Solaris

adding routes in Solaris

Solaris Guru's What is the proper way to add routes in the routing table so after a node reboot the routes will not be lost. I understand the /etc/defaultrouter for the default router and the <route add> command but using this command routes will be removed once the node reboots. Thanks (7 Replies)
Discussion started by: Brad_52000
7 Replies

5. IP Networking

How to delete some ipv6 routes?

Hi, How can i delete the following routes on my OpenBSD 4.1 system? # route -n show (including only relevant ipv6-routes) Internet6: Destination Gateway Flags Refs Use Mtu Interface ::/104 ::1 UGRS 1 0 ... (1 Reply)
Discussion started by: phalcos
1 Replies

6. AIX

Static Routes question

I added a static route through smit using: Communications applications and Services ==> TCIP/IP ==> Further Configuration ==> Static Routes ==> Add a Static Route ==> Route Type of host Filled in Destination Address, Default Gateway Address and Network Interface of en0. This... (2 Replies)
Discussion started by: jyoung
2 Replies

7. UNIX for Dummies Questions & Answers

Routes being automatically added

Hello, I have two AIX 5.3 servers that are supposedly set up exactly the same. The problem I am having is on one of the servers, it seems dynamic routes are being added mysteriously and non-periodically. This only happens on one server and not the other. Also, there doesn't seem to be a specific... (1 Reply)
Discussion started by: Conutmonky
1 Replies

8. UNIX for Dummies Questions & Answers

How does unix system administration, unix programming, unix network programming differ?

How does unix system administration, unix programming, unix network programming differ? Please help. (0 Replies)
Discussion started by: thulasidharan2k
0 Replies

9. SCO

Static routes in SCO

Hi, Just a question of thought. Why one needs to add static routes on Unix servers ? If I had ethernet card, it already has the settings for gateway for incoming and outgoing requests. We donot have to explicitly set the route it should take. Then what is the use... (3 Replies)
Discussion started by: dextergenious
3 Replies

10. Red Hat

How to set static routes for packets, within the same Network?

I have three systems A,B,C. I want to configure A in such a way that all packets from A to C goes via B. I tried: 1. ip route add 'ip of C' via 'ip of B' 2. route add -net 'net address' netmask gw 'ip of B' These commands work initially when I try a ping or traceroute and expire after... (2 Replies)
Discussion started by: kanak
2 Replies
netstat-nat(1)						      General Commands Manual						    netstat-nat(1)

NAME
netstat-nat - Show the natted connections on a linux iptable firewall SYNOPSIS
netstat-nat [options] DESCRIPTION
netstat-nat Displays NAT connections managed by netfilter/iptables which comes with the > 2.4.x linux kernels. The program reads its information from '/proc/net/ip_conntrack' or '/proc/net/nf_conntrack', which is the temporary conntrack-storage of netfilter. OPTIONS
-h displays help -n don't resolve IPs/portnumbers to host/portnames -p <protocol> display NAT connections with protocol selection (see /etc/protocols) -s <source host> display connections by source IP/hostname -d <destination host> display connections by destination IP/hostname -S display SNAT connections -D display DNAT connections -L display only connections to NAT box self (doesn't show SNAT & DNAT) -R display only connections routed through the NAT box (doesn't show SNAT & DNAT) -x extended view of hostnames -r <src|dst|src-port|dst-port|state> sort connections -o no output header -N display NAT box connection information (only valid with SNAT & DNAT) -v prints version FILES
/proc/net/ip_conntrack or /proc/net/nf_conntrack SEE ALSO
http://www.tweegy.nl/projects/netstat-nat/ http://www.netfilter.org/ AUTHOR
netstat-nat has been written by D.Wijsman danny@tweegy.nl The manual page has been written by marceln@xs4all.nl July 2002 netstat-nat(1)
All times are GMT -4. The time now is 07:33 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy