03-23-2010
6 More Discussions You Might Find Interesting
1. Solaris
Hi Folks,
I am used to writing scripts to get info by running commands at local zones level from their respective global zone by using zlogin <localzone> "command>" while remaining at the global zone level.
Can the same be done with Guest LDoms while remaining at the control LDOM level?
... (4 Replies)
Discussion started by: momin
4 Replies
2. Solaris
Solaris for Sparc 11.1 with the latest patches. Created a Guest LDOM with two vnet's net0 and net1, installed a guest whole root, ip exclusive zone that I want to be able to utilize DHCP. I have been able to create the zone but unable to get it to boot because I am unable to assign an anet to it.... (4 Replies)
Discussion started by: os2mac
4 Replies
3. UNIX for Dummies Questions & Answers
Hi!
I am not sure if this is the right place to post this question. What I did was to download vmware onto my laptop, them install a linux distro as a guest O.S., on VM network configuration I have used "bridge", them I used Virtual Network Editor to chose the network interface, but as I write... (4 Replies)
Discussion started by: fretagi
4 Replies
4. Solaris
Hi,
There is LDOM Guest where I need to expand /u02 file systems on it.
It is residing on a Solaris 11 Hypervisor (Primary Domain).
The storage is expanded on vdisk presented to Hypervisor.
I need steps to expand the /u02 on LDOM Guest. (2 Replies)
Discussion started by: vidya_sagar2003
2 Replies
5. Solaris
hello to everyone. im new member here.
i have a problem with a guest ldom on solaris 11 sparc in a T8. I need to access to disk vds assigned to guest domain but from control domain.
I want to modify a parameter in inittab of the guest domain because start guest domain give me problems... (2 Replies)
Discussion started by: Liam_
2 Replies
6. UNIX for Beginners Questions & Answers
I'm really stuck here. I've created an LDOM on a SPARC T4-1 with Solaris 11.4 to run a copy of Linux for SPARC. I got the Linux ISO installed and Linux itself installed and booted OK. The only thing is is that there's no networking available in the Linux guest.
This question is basically the... (7 Replies)
Discussion started by: Michele31416
7 Replies
NICE(1) BSD General Commands Manual NICE(1)
NAME
nice -- execute a utility at an altered scheduling priority
SYNOPSIS
nice [-n increment] utility [argument ...]
DESCRIPTION
The nice utility runs utility at an altered scheduling priority, by incrementing its ``nice'' value by the specified increment, or a default
value of 10. The lower the nice value of a process, the higher its scheduling priority.
The superuser may specify a negative increment in order to run a utility with a higher scheduling priority.
Some shells may provide a builtin nice command which is similar or identical to this utility. Consult the builtin(1) manual page.
ENVIRONMENT
The PATH environment variable is used to locate the requested utility if the name contains no '/' characters.
EXIT STATUS
If utility is invoked, the exit status of nice is the exit status of utility.
An exit status of 126 indicates utility was found, but could not be executed. An exit status of 127 indicates utility could not be found.
EXAMPLES
Execute utility 'date' at priority 5 assuming the priority of the shell is 0:
nice -n 5 date
Execute utility 'date' at priority -19 assuming the priority of the shell is 0 and you are the super-user:
nice -n 16 nice -n -35 date
COMPATIBILITY
The traditional -increment option has been deprecated but is still supported.
SEE ALSO
builtin(1), csh(1), idprio(1), rtprio(1), getpriority(2), setpriority(2), renice(8)
STANDARDS
The nice utility conforms to IEEE Std 1003.1-2001 (``POSIX.1'').
HISTORY
A nice utility appeared in Version 4 AT&T UNIX.
BSD
February 24, 2011 BSD