03-23-2010
6 More Discussions You Might Find Interesting
1. Solaris
Hi Folks,
I am used to writing scripts to get info by running commands at local zones level from their respective global zone by using zlogin <localzone> "command>" while remaining at the global zone level.
Can the same be done with Guest LDoms while remaining at the control LDOM level?
... (4 Replies)
Discussion started by: momin
4 Replies
2. Solaris
Solaris for Sparc 11.1 with the latest patches. Created a Guest LDOM with two vnet's net0 and net1, installed a guest whole root, ip exclusive zone that I want to be able to utilize DHCP. I have been able to create the zone but unable to get it to boot because I am unable to assign an anet to it.... (4 Replies)
Discussion started by: os2mac
4 Replies
3. UNIX for Dummies Questions & Answers
Hi!
I am not sure if this is the right place to post this question. What I did was to download vmware onto my laptop, them install a linux distro as a guest O.S., on VM network configuration I have used "bridge", them I used Virtual Network Editor to chose the network interface, but as I write... (4 Replies)
Discussion started by: fretagi
4 Replies
4. Solaris
Hi,
There is LDOM Guest where I need to expand /u02 file systems on it.
It is residing on a Solaris 11 Hypervisor (Primary Domain).
The storage is expanded on vdisk presented to Hypervisor.
I need steps to expand the /u02 on LDOM Guest. (2 Replies)
Discussion started by: vidya_sagar2003
2 Replies
5. Solaris
hello to everyone. im new member here.
i have a problem with a guest ldom on solaris 11 sparc in a T8. I need to access to disk vds assigned to guest domain but from control domain.
I want to modify a parameter in inittab of the guest domain because start guest domain give me problems... (2 Replies)
Discussion started by: Liam_
2 Replies
6. UNIX for Beginners Questions & Answers
I'm really stuck here. I've created an LDOM on a SPARC T4-1 with Solaris 11.4 to run a copy of Linux for SPARC. I got the Linux ISO installed and Linux itself installed and booted OK. The only thing is is that there's no networking available in the Linux guest.
This question is basically the... (7 Replies)
Discussion started by: Michele31416
7 Replies
NICE(1) BSD General Commands Manual NICE(1)
NAME
nice -- execute a utility with an altered scheduling priority
SYNOPSIS
nice [-n increment] utility [argument ...]
DESCRIPTION
nice runs utility at an altered scheduling priority. If an increment is given, it is used; otherwise an increment of 10 is assumed. The
super-user can run utilities with priorities higher than normal by using a negative increment. The priority can be adjusted over a range of
-20 (the highest) to 20 (the lowest). A priority of 19 or 20 will prevent a process from taking any cycles from others at nice 0 or better.
Available options:
-n increment
A positive or negative decimal integer used to modify the system scheduling priority of utility.
EXIT STATUS
The nice utility exits with one of the following values:
1-125 An error occurred in the nice utility.
126 The utility was found but could not be invoked.
127 The utility could not be found.
Otherwise, the exit status of nice will be that of utility.
COMPATIBILITY
The historic -increment option has been deprecated but is still supported in this implementation.
SEE ALSO
csh(1), getpriority(2), setpriority(2), renice(8)
STANDARDS
The nice utility conforms to IEEE Std 1003.2-1992 (``POSIX.2'').
HISTORY
A nice utility appeared in Version 6 AT&T UNIX.
BUGS
nice is built into csh(1) with a slightly different syntax than described here. The form 'nice +10' nices to positive nice, and 'nice -10'
can be used by the super-user to give a process more of the processor.
BSD
June 6, 1993 BSD