03-23-2010
From the primary domain you could:
ldm panic ldom1
telnet 0 5001
ok> boot
7 More Discussions You Might Find Interesting
1. AIX
Hi All!
My db2 is started in the AIX /etc/inittab on systemreboot as follows
db3:2:once:su - db2inst3 -c db2start >/dev/console 2>1
I changed the .profile of db2inst3 to put an alias to the db2start command as follows
alias db2start="/usr/bin/ksh /home/db2inst3/sample/db2start.ksh"
When... (1 Reply)
Discussion started by: voorkey
1 Replies
2. Solaris
Hi Guru's
Can any want here could explain to me the different between soft reboot and hard reboot .
Best Regards
Seelan (3 Replies)
Discussion started by: seelan3
3 Replies
3. Solaris
Hi,
Can someone explain in detail what 'uptime' ,'last reboot' and 'who -b' commands do in solaris.
this commands are not executing in every solaris box. why this is happening. Has solaris got some inbuilt commands into it. If yes then where i have found them?
Thanks,Soubhik (6 Replies)
Discussion started by: soubmukh
6 Replies
4. Shell Programming and Scripting
Can someone help me to convert the date format after get it from the "LAST REBOOT" command.
these is the standard output.
bash-3.00# last reboot
reboot system boot Fri Aug 6 15:07
reboot system down Fri Aug 6 15:04
reboot system boot ... (3 Replies)
Discussion started by: pichitw
3 Replies
5. Solaris
Hi
What are all the command outputs we have to note and keep it for safe before rebooting or shutting down a solaris box (5 Replies)
Discussion started by: newtoaixos
5 Replies
6. Shell Programming and Scripting
This is probably a simple question, but I'm new with writing scripts for Linux (IPFire in this case) and Google wasn't helpful with this.
When creating a script, what is the best and/or proper way to have it exit automatically if the reboot or shutdown command is given? If that's even... (2 Replies)
Discussion started by: bartgrefte
2 Replies
7. Solaris
Hi People,
I have been trying to learn solaris ldoms, have created one on a T2000 and get the following error when try to install it off DVD
WARNING: /virtual-devices@100/channel-devices@200/disk@1: Communication error with Virtual Disk Server using Port 0. Retrying
If anyone could help... (8 Replies)
Discussion started by: callmebob
8 Replies
LEARN ABOUT CENTOS
telnet-probe
TELNET-PROBE(1) General Commands Manual TELNET-PROBE(1)
NAME
telnet-probe - lightweight telnet-like port probe
SYNOPSIS
$PCP_BINADM_DIR/telnet-probe [-c] [-v] host port
DESCRIPTION
telnet-probe allows the pmdashping(1) daemons to establish connections to arbitrary local and remote service-providing daemons so that
response time and service availability information can be obtained.
The required host and port number arguments have the same meaning as their telnet(1) equivalents.
The -c option causes telnet-probe to perform a connect(2) only. This skips the read(2) and write(2) exercise that would otherwise be done
after connecting (see below).
The -v option causes telnet-probe to be verbose while operating.
Once the telnet connection has been established, telnet-probe reads from stdin until end-of-file, and writes all the input data to the tel-
net connection. Next, telnet-probe will read from the telnet connection until end-of-file, discarding whatever data it receives. Then
telnet-probe exits.
To operate successfully, the input passed via telnet-probe to the remote service must be sufficient to cause the remote service to close
the connection when the last line of input has been processed, e.g. ending with ``quit'' when probing SMTP on port 25.
By default telnet-probe will not produce any output, unless there is an error in which case a diagnostic message can be displayed (in ver-
bose mode only) and the exit status will be non-zero indicating a failure.
PCP ENVIRONMENT
Environment variables with the prefix PCP_ are used to parameterize the file and directory names used by PCP. On each installation, the
file /etc/pcp.conf contains the local values for these variables. The $PCP_CONF variable may be used to specify an alternative configura-
tion file, as described in pcp.conf(5).
DIAGNOSTICS
If telnet-probe succeeds, then 0 will be returned. If the attempt to establish a connection fails or is terminated, then a non-zero exit
status is returned.
SEE ALSO
PCPintro(1), pmdashping(1), pmie(1), telnet(1), connect(2), read(2) and write(2).
Performance Co-Pilot PCP TELNET-PROBE(1)