03-21-2010
check cfgadm -al to check if its connected. if yes, try this.
luxadm -e forcelip /devices/pci@1d,700000/SUNW,qlc@1,1/fp@0,0:devctl
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi,
is there a way to get information of an annex device connected to port A ? i need to get the I.P address of the annex and the port
it connected to on the annex.
dori (1 Reply)
Discussion started by: dorilevy
1 Replies
2. UNIX for Advanced & Expert Users
Please, can someone tell me why my SunBlade would be showing 2 different but similar MAC addresses on the same port on the Switch? The switch shows all other Workstations with 1 MAC on each port, but the SunBlade is showing 2. Thanks in advance for any insight.... (1 Reply)
Discussion started by: GoneCrazy
1 Replies
3. Shell Programming and Scripting
H,
I want to know the ip of the devices connected to a specific port.
Suppose 2 s/m's are connected to port 3092. I want to get the ip of those system's .
how do i get it? (1 Reply)
Discussion started by: madhumathikv
1 Replies
4. UNIX for Dummies Questions & Answers
I currently access a remote Unix server which has an external modem connected to one of it's serial ports (/dev/cua/b). At times, this server undergoes a hard reset and for some reason this disallows us from making use of the modem any longer. A hard reset of the modem always seems to fix the... (0 Replies)
Discussion started by: ebender1
0 Replies
5. Solaris
I understand that fcinfo hba-port should show information(WWN, HBA vendor, etc..) but my result show "No adapter found". If I used grep -i 'version' /var/adm/messages* then I see my installed HBA (QLogic FCode at 2.00.09).. I am wondering why and what I had failed to install?
Thanks in advance.... (23 Replies)
Discussion started by: Y4Net
23 Replies
6. UNIX for Advanced & Expert Users
Hey guys,
I need to kill the process that is currently connected to port 10540. I'm on HP-UX machine.
Below is the result of my netstat.
$ netstat -an |grep 10540
tcp 0 0 129.0.0.1.10540 *.* LISTEN
We don't have lsof command, but we have fuser.
... (3 Replies)
Discussion started by: brichigo
3 Replies
7. Solaris
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies
8. Solaris
Hi, I have a question regarding HBA configuration. Here are the commands' output:
# cfgadm -al | grep fc
c1 fc-fabric connected unconfigured unknown
c2 fc connected unconfigured unknown
c5 ... (11 Replies)
Discussion started by: aixlover
11 Replies
9. Solaris
please find the below o/p for your reference
bash-3.00# fcinfo hba-port
HBA Port WWN: 21000024ff295a34
OS Device Name: /dev/cfg/c2
Manufacturer: QLogic Corp.
Model: 375-3356-02
Firmware Version: 05.03.02
FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies
LEARN ABOUT DEBIAN
twinstar
TWINSTAR(8) User Contributed Perl Documentation TWINSTAR(8)
NAME
twinstar - Control the Twinstar feature of a Xorcom Astribank
SYNOPSIS
twinstar {status|jump|enable-wd|disable-wd|ports}
DESCRIPTION
twinstar is a tool to control the Twinstar (dual USB port) of a Xorcom Astribank. There is a single and mandatory argument which is the
command to run. That command operates on all the Astribanks connected to the system.
Technically all the commands are implemented using Dahdi::Xpp::Mpp which in turn uses astribank_tool. Thus using thus tool will require
root permissions or otherwise read/write permissions to the USB device.
The twinstar may be in watchdog mode, which means that it will jump to the remote host if it loses contact with the local host. This can
happen if the machine is powered down or hangs or even if the xpp drivers are unloaded. Which is why the standard twinstar scripts put the
Astribanks in twinstar mode on startup and remove it on normal shutdown.
An Astribank will only jump to the other host (either if asked explicitly or by the watchdog) only if there is a different Astribank
connected to the other port and running. Which is why all of this has no effect on systems that don't need this functionality.
The command are:
status
Shows the current status of all Astribanks. Note that it only shows Astribanks whose current active USB port is the one connected to this
computer.
Example output:
DEVICE PORT WATCHDOG POWER0 POWER1
usb:001/010 0 on yes yes
usb:001/011 0 on yes yes
For each Astribank on the system that has Twinstar support we get:
Device
The address of the device. This is the bus address, e.g. the address you see in lsusb / dahdi_hardware.
Port
The active USB port on the Astribank. This should be always '0' on the master and always 1 on the slave.
Watchdog
on if the watchdog is triggered in the Atribank or off otherwise.
Power0, Power1
Shows which ports of this Astribank are connected to a USB port of a running computer. This only shows whether or not the USB host
provides power.
ports
Shows the same 'Port' column of the status command.
jump
Command all the Astribanks to jump to the other port. This works regardless the watchdog mode is enabled or not. But requires that there is
power on the other port.
enable-wd
Enables watchdog mode.
disable-wd
Disables watchdog mode.
FILES
twinstar mostly uses astribank_tool which in turn mostly uses USB files under /dev/bus/usb .
perl v5.14.2 2010-07-28 TWINSTAR(8)