What ever packet u send it will hit 10.155.24.1 first .
For the path you can use "traceroute"
So, is it 0.0.0.0 mean any IP address or destined address ??
So, can I remove below two entries ??
As the entry start 0.0.0.0 already represent all IP route to 10.155.24.1 ??
Please advice ....
Hi,
I'm trying to connect to a network device, with the connection follwoing the UNIX routing table we set up. Its to go via a specific network Gateway and out throught a specific Lan card (Lan4). However when trying to conenct it keeps going through Lan3 and will not get to its destination.... (3 Replies)
Is ther a way to retain say, a default gateway entered in a routing table after a reboot? I end up always having to re-enter my default gateway after I reboot my system.
Thanks! (4 Replies)
hi all...
i need to know, where is locate the routing table on sun solaris, how i can saved the configuration....
because when i restart the server, lost the configuration....
thank you...
Regards... (3 Replies)
Hi all,
I am confusing with routing table, i use linux and iptables.
i have 1 internet gateway, and 1 router for VPN.
here is my network.
eth0=192.168.0.1
eth1=192.168.100.1
192.168.0.0/24 --- eth0(Linux Box)eth1 ---(DSL)---Internet
|
... (4 Replies)
Hello.
Is there any way to restore back the default ip routing table ?
For example, my current routing table is something like
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
109.123.95.0 0.0.0.0 255.255.255.0 U 0 ... (0 Replies)
Hi all,
Could someone please explain to me how I should read this routing table,
# netstat -rn
Routing tables
Destination Gateway Flags Refs Interface Pmtu
127.0.0.1 127.0.0.1 UH 0 lo0 32808
10.222.47.82 10.222.47.82 UH... (3 Replies)
Discussion started by: rachael
3 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)