Sponsored Content
Full Discussion: Disk or CDROM problem?
Operating Systems Solaris Disk or CDROM problem? Post 302399883 by incredible on Monday 1st of March 2010 11:26:39 PM
Old 03-02-2010
Hi
1) yes, you can see the errors even if the cdrom drive is not used at all
2) this is how the OS sees the devices, via controller numbers and target id etc.
you can check the device path from ok> prompt too , using devalias

3) yes, you may not wish to replace the drive and continue using the system
BUT, a caution!! if your system corrupts for any reason and if there's a need rise to use the drive to boot from cdrom, THEN YOU WILL have a problem..
SO suggest to just replace it.
 

3 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Cdrom Problem!!!

Hi everybody: I have Solaris 8 installed on my little Enterprise 3500 and, for a cruel fate of the destiny, Im the admin.... Here is the problem: a week ago I took out a CD from the CDROM drive in an abnormal way. I inserted a clip in the little hole in the front of the drive because the button... (8 Replies)
Discussion started by: piltrafa
8 Replies

2. Solaris

Ultra 2 CDROM Problem

I have a Ultra 2 running solaris9, I'm trying to do a boot cdrom to install Solaris 10. During the boot, the system can't find the CDROM drive. It shows up during a probe-scsi-all. Also, when booted to Solaris 9 I place a CD in the drive it takes almost 10 minutes before the CD is readable on the... (6 Replies)
Discussion started by: stocksj
6 Replies

3. AIX

problem on sharing cdrom drive in AIX with linux

HI i have setuped a nfs between a AIX system and a linux os ,keeping AIX as sever i need to share the CDrom in AIX server with the linux operating system. ie. linux os machine does't have a cdrom . will i be able be share ..i tried a lot but it gives a message which resembles NFS access... (3 Replies)
Discussion started by: raguraja
3 Replies
HD(4)							     Linux Programmer's Manual							     HD(4)

NAME
hd - MFM/IDE hard disk devices DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave hdd. General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order the partitions are discovered, and only nonempty, nonextended partitions get a number. However, partition numbers 1-4 are given to the four partitions described in the MBR (the "primary" partitions), regardless of whether they are unused or extended. Thus, the first logi- cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions on an IDE disk. For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS "primary" partition on the second one. They are typically created by: mknod -m 660 /dev/hda b 3 0 mknod -m 660 /dev/hda1 b 3 1 mknod -m 660 /dev/hda2 b 3 2 ... mknod -m 660 /dev/hda8 b 3 8 mknod -m 660 /dev/hdb b 3 64 mknod -m 660 /dev/hdb1 b 3 65 mknod -m 660 /dev/hdb2 b 3 66 ... mknod -m 660 /dev/hdb8 b 3 72 chown root:disk /dev/hd* FILES
/dev/hd* SEE ALSO
chown(1), mknod(1), sd(4), mount(8) COLOPHON
This page is part of release 3.53 of the Linux man-pages project. A description of the project, and information about reporting bugs, can be found at http://www.kernel.org/doc/man-pages/. Linux 1992-12-17 HD(4)
All times are GMT -4. The time now is 05:15 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy