Hello, I've got a FreeBSD 6 server running on my network that I used as a file server for my main computer. However I've really become frustrated with the slow up/down speeds I'm getting, about 100KB/s, which is about as bad as if I was using a "real" server. My setup is as follows:
Code:
ISP
|
Router
|
Hub
|
PowerLine node
[~10m]
PowerLine node
|
FreeBSD 6 Sever (256MB/450MHz Pentium)
[~3M]
Powerline node
|
Main Computer (Win7 using FileZilla)
Here are the results of tracert:
Code:
Tracing route to 192.168.1.15 over a maximum of 30 hops
1 319 ms 266 ms 242 ms 192.168.1.15
Trace complete.
It seems to be since we're just going over the LAN, I should really be getting at least 500KB/s+ right? Is this a PowerLine issue, cable issue, FreeBSD issue, PC hardware isssue... etc? I'd be very thankful if I can get some ideas where to start to identify the bottleneck here, thanks a lot.
On one of of solaris 7 boxes whenever i telnet or ftp it takes sometime before i get the prompt...any quick ideas where I should look...Thanks (3 Replies)
One of our most frequent questions is how to automate ftp transfers. There are several approaches. Since I'm writing this post, we will start with my favorite technique. :)
In Automated FTP task I present a simple example of my ksh co-process technique. And note that later in this thread I... (0 Replies)
just as the title says.
thanks.
#General Rule Sets
/sbin/ipfw add 0300 check-state
/sbin/ipfw add 0301 deny tcp from any to any in established
/sbin/ipfw add 0302 pass tcp from any to any out setup keep-state
/sbin/ipfw add 0303 pass udp from any to any out
#SSH FTP
/sbin/ipfw add 0400... (11 Replies)
When I ssh to my box, an Ultra 5. I get prompted for password immediately. I enter it and have to wait sometimes a full minute for it to prompt for a password.
The same thing happens when i try to ftp to the box, it will say connected, but it takes forever to prompt for password, and... (2 Replies)
SCO Unix 5.0.5 moving to Red Hat
Intel EtherExpress Pro/100+
Newbie that just started working for a company and having an issue with transfer speeds over the network. Need to move 1.5GB of data from an old server with a single SCSI HDD to a new server with RAID 5 SATA HDD's. Goal was to FTP... (4 Replies)
Hi again guys,
Earlier today, just all of a sudden, all SSH and FTP connections to my internal Linux box just slowed down to a crawl. After the connection/authentication though, everything was back to normal speed. Until you have to connect again. A box reboot didnt work either.
Now, from... (1 Reply)
How can one find the name and size of files ftp'ed during an old ftp transfer.
Is there any log where these details are stored or any UNIX command which can provide these details.
Thanks in advance. (4 Replies)
Hi All.
We are using AIX 5.3 ML9. There is 1 Gig NIC installed on two servers (Primary and Secondary) with Full Duplex Mode. We have scheduled a cronjob to copy the backup from primary to secondary thru FTP on WAN. The total data size is 15 GB and it took 9 Hours and 18 Mins with transfer rate... (6 Replies)
hi,
good morning.
Ma trying to ftp from one AIX machine to another on the same segment of the network. The ftp to eshtablish connection from machine A to machine B is quick, but the reverse is taking is much time (2 mins).
anyone can help me to solve this issue please (1 Reply)
Hello all. I have VSFTP up and ruining on ubuntu 10.04. It works great inside LAN, however when it comes to using it outside i have some problems. If i try to connect from filezila i get the listing and if i try to download it shows it will take forever to receive a file which is larger then 1mb,... (2 Replies)
Discussion started by: mantas1
2 Replies
LEARN ABOUT SUSE
tgt-setup-lun
tgt-setup-lun(8) System Manager's Manual tgt-setup-lun(8)NAME
tgt-setup-lun - creates a target, adds a device to the target and defines initiators that can connect to the target
SYNOPSIS
tgt-setup-lun -d device -n target_name [initiator_IP1 initiator_IP2 ...] [-h]
DESCRIPTION
Starts tgtd if necessary and creates a target according to the supplied target_name. The format of the target name is as follows:
iqn.2001-04.com.<hostname>-<target_name> The target name must be unique.
The script then adds the requested device to the target. If specific IP addresses are defined, it adds them to the list of allowed initia-
tors for that target. If no IP addresses is defined, it defines that the target accepts any initiator.
EXAMPLES
Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81:
tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81
Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81 and 192.168.10.82:
tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81 192.168.10.82
Create a target that uses /dev/sdb1 and allows connections from any initiator:
tgt-setup-lun -d /dev/sdb1 -n my_target
Display help:
tgt-setup-lun -h
AUTHOR
Written by Erez Zilber
REPORTING BUGS
Report bugs to <erezz@voltaire.com>.
COPYRIGHT
Copyright (C) Voltaire Ltd. 2008.
tgt-setup-lun(8)
01-28-2010
