|
|
Sponsored Content
Operating Systems
SCO
SCO 5.0.7 no root disk controller found error during install
Post 302389128 by FrictionBurn on Friday 22nd of January 2010 05:55:48 PM
01-22-2010
|
|
10 More Discussions You Might Find Interesting
1. SCO
Hi,
I have an openserver 5.0.0 machine in the office. The sysad of that machine left years ago without leaving the password to anyone.
I was wondering if someone has a copy of the boot / root diskettes (rescue) for this version? Or perhaps if anyone knows a download link / location in the... (0 Replies)
Discussion started by: marcpascual
0 Replies
2. SCO
New IBM x3400 machine with a raid 5 configuration. Go through the early setup routine to the point where I answer the questions for time zone, machine name. Enter continue and get a message stating :
"Incorrect disk partitioning cannot continue" This is a sco message, refers to the installation... (1 Reply)
Discussion started by: wjbtms
1 Replies
3. Solaris
Hi,
I am a newbie to Solaris. I want to know how to find out the controller target and disk number on a SunFire V890 box that has 6X72GB disks. The probe-scsi output is as shown below:
/pci@8,600000/SUNW,qlc@2
LiD HA LUN --- Port WWN --- ----- Disk description -----
0 0 0 ... (1 Reply)
Discussion started by: sudhir_shet
1 Replies
4. SCO
hi all
i use sco open server reliseas 5 on my system i get an image from system hard disk to another hard disk with acronis software and start system with new(backup)hard disk, but during the boot process some errors generate as follow
warning:hd:noroot disk controler was found
hd:a boot-time... (2 Replies)
Discussion started by: mehran_malek
2 Replies
5. SCO
hi...
i hav a problem to install sco unix
while installing sco unix 5.0.5 in acer altos with hardware raid
am getting error
"Warning HD: no root disk controller was found
system error 5: while getting fs type
flushing controller: DAC960PRL cache done."
i hav use the following... (18 Replies)
Discussion started by: mselvaprakash
18 Replies
6. SCO
So today I tried to upgrade a customer from a Proliant with an HPSAS controller to an Intel server with a MEGASAS controller.
First, I downloaded the megasas driver from SCO and installed it on the old system.
Then I created a new Microlite Edge emergency boot cd with the new driver on it.
I... (2 Replies)
Discussion started by: jgt
2 Replies
7. SCO
Installing SCO UNIX 507 on Dell Poweredge T610. It has no floppy so I downloaded the BTLD onto CD from SCO site to load without floppy drive. BTLD loads ok. when i get to the Media to be used, no matter what option i chose i get the error: No controller for device you have chosen. During bootup you... (9 Replies)
Discussion started by: romanglad112
9 Replies
8. SCO
Hi,
We have an old SCO Openserver 5.0.7 server that I have inherited that currently has two issues that we are trying to resolve.
1. We do not know the root password. I have contacted the old admin, looked for rescue disk and documentation but there appears to be nothing.
I have tried... (1 Reply)
Discussion started by: acerimmer10
1 Replies
9. Solaris
Hi
The scenario in the oracle t4-1 hardware with solaris 10 is as follows:
1. The initial install on the server was performed with an incorrect disk layout.
2. New disks were ordered and slot into the server.
3. The disks are allocated a controller and a disk number based on the disk or... (13 Replies)
Discussion started by: kerrygold
13 Replies
10. SCO
I am working on a system that uses SCO Unix 5. I started later in this troubleshooting process so I have had to play catch up on some of the earlier mistakes that were made.
The HD was formatted using the SCSI controller cards bios.
I have 2 recovery floppies the boot and the root.
After... (19 Replies)
Discussion started by: graysona
19 Replies
LEARN ABOUT HPUX
set_link
set link(1m) set link(1m) NAME
set link - Changes the value of a modifiable, single-valued attribute of a soft link SYNOPSIS
cdscp set link link-name attribute-name = attribute-value ARGUMENTS
The full name of the soft link. The name of the attribute to be modified. Specify only one attribute at a time. See Description for valid attribute names. The value of a particular attribute. DESCRIPTION
The set link command changes the value of a modifiable, single-valued attribute of a soft link. The following are valid attributes: Speci- fies the full name of the directory, object entry, or other soft link to which the soft link points. Specifies a timeout value after which the soft link is either checked or deleted. The timeout value contains both an expiration time and an extension time. If a soft link expires and its target entry is deleted, the soft link is deleted. If the soft link still points to an existing entry, its life is extended by the expiration time. Specify expiration-time in the format yyyy-mm-dd-hh:mm:ss (year-month-day-hour:minute:second). Specify extension- time in the format ddd-hh:mm:ss (day-hour:minute:second). Privilege Required You must have write permission to the soft link. NOTE
This command is replaced at Revision 1.1 by the dcecp command and may not be provided in future releases of DCE. EXAMPLE
The following command redirects a soft link named /.:/admin/work_disk from its current destination name, /.:/admin/work_disk01, to a new destination name, /.:/admin/work_disk03. cdscp> set link /.:/admin/work_disk CDS_LinkTarget = /.:/admin/work_disk03 RELATED INFORMATION
Commands: create link(1m), delete link(1m), list link(1m), show link(1m) set link(1m)