01-22-2010
SCO 5.0.7 no root disk controller found error during install
I'm "attempting" to install SCO 5.0.7 on an HP ML370 G4 server and am ready to bash the keyboard with head now. I keep getting the error message "WARNING hd: no root disk controller found" when running the bootable install cd.
I have a raid 5 array with an online spare created using 4 36.3 GB drives on an HP 6400 smart array controller using smart start 7.1 and 1 logical drive configured on said array and a tape drive on the array controler as well. The onboard raid controllers have been disabled in the bios and nothing is attached to them. On bootup you can see the controlled being initialized and the drives in the array spinning up and it recognizes the logical drive.
I've tried using several variations on the defbootstr but still nothing seems to work so now i'm a bit stuck. Below is what I thought was the proper loader
defbootstr link=ciss hd=Sdsk Sdsk=ciss Srom=wd(0,0,0,0)
but alas, no luck so far. Does anyone have any suggestions?
Regards
10 More Discussions You Might Find Interesting
1. SCO
Hi,
I have an openserver 5.0.0 machine in the office. The sysad of that machine left years ago without leaving the password to anyone.
I was wondering if someone has a copy of the boot / root diskettes (rescue) for this version? Or perhaps if anyone knows a download link / location in the... (0 Replies)
Discussion started by: marcpascual
0 Replies
2. SCO
New IBM x3400 machine with a raid 5 configuration. Go through the early setup routine to the point where I answer the questions for time zone, machine name. Enter continue and get a message stating :
"Incorrect disk partitioning cannot continue" This is a sco message, refers to the installation... (1 Reply)
Discussion started by: wjbtms
1 Replies
3. Solaris
Hi,
I am a newbie to Solaris. I want to know how to find out the controller target and disk number on a SunFire V890 box that has 6X72GB disks. The probe-scsi output is as shown below:
/pci@8,600000/SUNW,qlc@2
LiD HA LUN --- Port WWN --- ----- Disk description -----
0 0 0 ... (1 Reply)
Discussion started by: sudhir_shet
1 Replies
4. SCO
hi all
i use sco open server reliseas 5 on my system i get an image from system hard disk to another hard disk with acronis software and start system with new(backup)hard disk, but during the boot process some errors generate as follow
warning:hd:noroot disk controler was found
hd:a boot-time... (2 Replies)
Discussion started by: mehran_malek
2 Replies
5. SCO
hi...
i hav a problem to install sco unix
while installing sco unix 5.0.5 in acer altos with hardware raid
am getting error
"Warning HD: no root disk controller was found
system error 5: while getting fs type
flushing controller: DAC960PRL cache done."
i hav use the following... (18 Replies)
Discussion started by: mselvaprakash
18 Replies
6. SCO
So today I tried to upgrade a customer from a Proliant with an HPSAS controller to an Intel server with a MEGASAS controller.
First, I downloaded the megasas driver from SCO and installed it on the old system.
Then I created a new Microlite Edge emergency boot cd with the new driver on it.
I... (2 Replies)
Discussion started by: jgt
2 Replies
7. SCO
Installing SCO UNIX 507 on Dell Poweredge T610. It has no floppy so I downloaded the BTLD onto CD from SCO site to load without floppy drive. BTLD loads ok. when i get to the Media to be used, no matter what option i chose i get the error: No controller for device you have chosen. During bootup you... (9 Replies)
Discussion started by: romanglad112
9 Replies
8. SCO
Hi,
We have an old SCO Openserver 5.0.7 server that I have inherited that currently has two issues that we are trying to resolve.
1. We do not know the root password. I have contacted the old admin, looked for rescue disk and documentation but there appears to be nothing.
I have tried... (1 Reply)
Discussion started by: acerimmer10
1 Replies
9. Solaris
Hi
The scenario in the oracle t4-1 hardware with solaris 10 is as follows:
1. The initial install on the server was performed with an incorrect disk layout.
2. New disks were ordered and slot into the server.
3. The disks are allocated a controller and a disk number based on the disk or... (13 Replies)
Discussion started by: kerrygold
13 Replies
10. SCO
I am working on a system that uses SCO Unix 5. I started later in this troubleshooting process so I have had to play catch up on some of the earlier mistakes that were made.
The HD was formatted using the SCSI controller cards bios.
I have 2 recovery floppies the boot and the root.
After... (19 Replies)
Discussion started by: graysona
19 Replies
LEARN ABOUT CENTOS
installboot
installboot(1M) installboot(1M)
NAME
installboot - install bootblocks in a disk partition
SYNOPSIS
installboot bootblk raw-disk-device
The boot(1M) program, ufsboot, is loaded from disk by the bootblock program which resides in the boot area of a disk partition.
The ufs boot objects are platform-dependent, and reside in the /usr/platform/platform-name/lib/fs/ufs directory. The platform name can be
found using the -i option of uname(1).
The installboot utility is a SPARC only program. It is not supported on the architecture. users should use installgrub(1M) instead.
bootblk The name of the bootblock code.
raw-disk-device The name of the disk device onto which the bootblock code is to be installed; it must be a character device which is read-
able and writable. Naming conventions for a SCSI or IPI drive are c?t?d?s? and c?d?s? for an IDE drive.
Example 1: Installing UFS Boot Block
To install a ufs boot block on slice 0 of target 0 on controller 1 of the platform where the command is being run, use:
example# installboot /usr/platform/`uname -i`/lib/fs/ufs/bootblk
/dev/rdsk/c1t0d0s0
/usr/platform/platform-name/lib/fs/ufs
directory where ufs boot objects reside.
/platform/platform-name/ufsboot
second level program to boot from a disk or CD
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
od(1), uname(1), boot(1M), init(1M), kadb(1M), kernel(1M), monitor(1M), reboot(1M), rpc.bootparamd(1M), init.d(4), attributes(5)
WARNINGS
The installboot utility fails if the bootblk or openfirmware files do not exist or if the raw disk device is not a character device.
11 Apr 2005 installboot(1M)