Sponsored Content
Top Forums Programming C++/Java full-duplex communication Post 302385949 by fpmurphy on Sunday 10th of January 2010 09:12:56 PM
Old 01-10-2010
Here is a good introductory article on AMQP from Linux Journal which you should read.
 

10 More Discussions You Might Find Interesting

1. IP Networking

Problems switching to Full Duplex

We run Compaq UNIX Tru64 5.1. After a switch got replaced our ethernet-card was magically set to half duplex! We saw, that the card was set to Autonegotiate: vmunix: ee1: Autonegotiated, 100 Mbps full duplex So we set the card with ifconfig to 100 Mbps full duplex with the following... (3 Replies)
Discussion started by: arn_ch
3 Replies

2. UNIX for Dummies Questions & Answers

Full duplex at HUB?

Ok at the moment I have a hub whit 5 computers connected to it. It's a 10/100 NetGear hub. Ok I heard that there is some command I can run or a file I edit or something like that. But what the command/file/script/whatever does is tells you what connect speed it's connecting to the hub to. ... (4 Replies)
Discussion started by: merlin
4 Replies

3. UNIX for Dummies Questions & Answers

Full Duplex Howto

Dear Members, I was reading a few posts and saw something about installing two Nics so one could use Full Duplex. I remember back in the day of dial up, you could have two modems and use one for upstream and one for downstream. This was called shotgunning. It seems that you can now do the same... (4 Replies)
Discussion started by: Phobos
4 Replies

4. Programming

full -duplex ?

what is meant by full duplex and half duplex? b'coz in differences b\w hub and switch ,i heard lot this duplex word so please help me (1 Reply)
Discussion started by: parvathy
1 Replies

5. Solaris

100 gigabit full duplex

How can I tell on Solaris 9 sparc if my nics are running 100 gigabit full duplex... (4 Replies)
Discussion started by: csaunders
4 Replies

6. Red Hat

RedHat 9 Force full duplex

All, I have a RedHat 9 box which I need to figure out how to get it to stay in full duplex mode after a reboot. I have tried ethtool -s eth0 speed 100 duplex full autoneg off I have tried to add a line to the /etc/sysconfig/network-scripts/ifcfg-eth0 like this: ETHTOOL_OPTS="speed... (4 Replies)
Discussion started by: bubba112557
4 Replies

7. Solaris

How to force a full duplex

I need to change some Ip addresses for my servers to reflect in the NIS map. I also need to force full duplex on the 10/100 cards & 1/2 duplex in the 10 cards. I can change the IP by doing ifconfig <NIC card > plumb up <newip>. Not quite sure on how to force the full / half duplex & how to... (2 Replies)
Discussion started by: Remi
2 Replies

8. SuSE

configure full duplex

How do I configure full duplex on suse 8.2 I tried ethtool -s eth0 speed 100 duplex full autoneg off the above works but when I reboot the machine the configure was lost. How do I configure full duplex so that when the machine get rebooted the configuration will stay. My interface... (4 Replies)
Discussion started by: hassan2
4 Replies

9. UNIX for Advanced & Expert Users

How to set full duplex for solaris 5.5

I would like to change half duplex to full duplex on solaris 5.5. I tried with below commands but they didnt work on solaris 5.5. #ndd -set /dev/le adv_100fdx_cap 1 (6 Replies)
Discussion started by: csreenivas
6 Replies

10. Solaris

How to find half duplex or full duplex

Hi, How to find whether the server is running with half duplex or full duplex. I tried with the following command ndd -get /dev/ but am not getting any output,. Is the command correct? Also let me know how to change from half to full duplex. (1 Reply)
Discussion started by: rogerben
1 Replies
DACS.JAVA(7)						  DACS Miscellaneous Information					      DACS.JAVA(7)

NAME
dacs.java - DACS Java support DESCRIPTION
This document describes support for Java provided by DACS. To enable Java support, DACS must be configured using the --enable-java flag. It may also be necessary to specify the location of the Java commands and include files. See dacs.install(7)[1]. Note Java support is currently very limited and should be considered experimental. It is currently only possible to call dacsauth(1)[2] and dacscheck(1)[3] using the Java Native Interface (JNI) provided. The command line arguments to both of these commands are exactly as documented in their manual pages. Each argument is passed as a String. The code is not thread-safe and is probably not suitable for being called many times within a particular process due to assumptions it makes about dynamic memory allocation. There are no immediate plans to improve or extend Java support. Using the existing capability to build the JNI layer, however, it should not be difficult for an experienced Java programmer to build upon the example Java code provided. With Java support enabled, building DACS will copy the JNI shared library and a .jar file to the library directory (default: /usr/local/dacs/lib), and the JNI include files to the include directory (default: /usr/local/dacs/include). The tools/java/jni distribution directory contains a simple script called javarun that demonstrates how to run dacsauth or dacscheck as a Java application. For example, to validate the Unix password for user somebody, run (as root): ./javarun dacsauth -m unix suff -user somebody -prompt DIAGNOSTICS
The return codes are as documented in the command's manual page. AUTHOR
Distributed Systems Software (www.dss.ca[4]) COPYING
Copyright2003-2012 Distributed Systems Software. See the LICENSE[5] file that accompanies the distribution for licensing information. NOTES
1. dacs.install(7) http://dacs.dss.ca/man/dacs.install.7.html 2. dacsauth(1) http://dacs.dss.ca/man/dacsauth.1.html 3. dacscheck(1) http://dacs.dss.ca/man/dacscheck.1.html 4. www.dss.ca http://www.dss.ca 5. LICENSE http://dacs.dss.ca/man/../misc/LICENSE DACS 1.4.27b 10/22/2012 DACS.JAVA(7)
All times are GMT -4. The time now is 08:45 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy