01-10-2010
i think you've some glitches with your terminal software. if you press enter, it sends enter twice... i would recommend using another software for serial communication. you should try putty... works fine for me. or if you've a solaris laptop you can use a "tip" session.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
looking for the answer to console port access via 25pin serial. Can i tip in from another unix box for access? (5 Replies)
Discussion started by: simplimarvelous
5 Replies
2. AIX
I have installed aix 5.2 on aix box through serial console connected to COM 1 . I even get a login prompt after the fresh installation . But as soon as i give a root & enter i again get a login prompt.i..e I am not able to logon after a fresh installation.
and even i configured IP configuration... (0 Replies)
Discussion started by: linuxnightowl84
0 Replies
3. Solaris
Hi all,
After the V890 server shutdown unexpectedly, it became unaccessible from RSC. There is one error message about it: rscadm: RSC firmware not responding
Do you have experienced this? Please help! (1 Reply)
Discussion started by: bamboonix
1 Replies
4. UNIX for Dummies Questions & Answers
Hi everybody
i am trying to telnet to sun server from win xp machine but getting message "x21 error connection closed by remote user". i had make changes in /etc/default/login & /etc/fuser file still i have not getting telnet access. my win xp machines ip is 10.205.121.177 & sun server ip is... (1 Reply)
Discussion started by: pshelke
1 Replies
5. Solaris
Hi,
Can anyone suggest me any USB Hard Disk Drive which I can connect to Sun Fire V890 and take backup at a quick speed. A test with SolidState USB Hard Drive for backup work was taking writing at 2GB per hour for a 75GB backup.
Regards,
Tushar Kathe (1 Reply)
Discussion started by: tushar_kathe
1 Replies
6. Solaris
Hi,
I want to know if there is a command available for obtaining the BIOS Serial Number on a Sun Fire V240 machine? Or is it a known issue that it cannot be obtained through any command?
Thanks,
Vineet (4 Replies)
Discussion started by: vineetd
4 Replies
7. Solaris
Hi Gurus
I would like to know whether break command always work well means take the system to ok> prompt. Its depend upon sever model also. As I am facing problem when ever my system ( Sunfire V890 ) having Solaris 10 OS & oracle RAC on it goes to hang state then I run the break command from... (6 Replies)
Discussion started by: girish.batra
6 Replies
8. Solaris
I am battling to get a V890 up and running. The system appears to have AUTOBOOT=false, so no OS comes up when it's powered on, and I do not have the credentials to get to the RSC management console. Output to ttya serial console ends at "Probing I/O buses", I assume because output is then being... (4 Replies)
Discussion started by: dstmark
4 Replies
9. Solaris
Hi Oracle Hardware Specialists,
I have shutdown a Sun Fire X2200 server running Solaris 10 x86 to single user mode to experiment some backup commands using Web based Sun embedded Lights Out Manager Redirection to open up a console session. However, it is not possible to copy & past text with... (7 Replies)
Discussion started by: gjackson123
7 Replies
dc(7) Miscellaneous Information Manual dc(7)
NAME
dc - serial line/mouse/keyboard
SYNOPSIS
controller dc0 at ibus0 slot 0 vector dcintr
DESCRIPTION
The dc serial line controller provides DECstation 2100, DECstation 3100, DECstation 5000, and DECstation 5100 computer systems with key-
board, mouse, and serial communications interfaces. The serial communications interfaces on the DECstation 2100 and DECstation 3100 provide
partial modem control. The serial communications interfaces on the DECstation 5000 provide full modem control. The device special file
/dev/tty01 on a DECstation 5100 provides full modem control, while the remaining ports provide no modem control at all. All serial commu-
nications interfaces operate at baud rates from B50 to B9600, excluding B200.
The dc ports are used as follows: Usage Graphics device keyboard at 4800 BPS Mouse or tablet at 4800 BPS Communications port 1 (w/modem
control)/local terminal Communications port 2 (w/modem control)/local terminal
On all systems except the DECstation 5100, serial port 2 is used for the system console port in server (that is, non-graphics) configura-
tions. On DECstation 5100s, the serial port labeled 3 on the back of the system is always the system console port. The serial system con-
sole port always operates at 9600 BPS, 8-bits, no parity; modem control is not supported.
RESTRICTIONS
Data communications equipment attached to the console serial port in server configurations must be set to 9600 BPS, 8-bits, no parity. The
scc driver enforces this restriction.
FILES
console terminal local terminal local terminal local terminal (DECstation 5100 only)
RELATED INFORMATION
console(7), devio(7), tty(7), MAKEDEV(8) delim off
dc(7)