Are you looking to set up a local ntp time server for a group of systems so that their time is synchronized?
If this is the case, you can configure a local timer server as follows (assuming your local network is 192.168.0*):
and point the the other systems at this time server.
Hi,
I have a problem using NTP.
We have a setup as following :
client --> HP Server(NTP) --> DMZ server --> DMZ server --> Internet
Only some clients and our HP server is using NTP, the others are using different software.
Now I get an error every day :
Oct 1 13:17:15 nlunx1n1 xntpd:... (4 Replies)
Dear All
I'm solaris user . I need to setup NTP authentication for my office server but I have some question for ntp setting up. I need to know if i set authen NTP the client that doesn't set for authen key can sync time from authen ntp server or not ?? when i setup the authen at ntp server ... (1 Reply)
All -
i tried to sysn the clock from our server to get the timing and the server IP has been added in the ntp.conf file and i have some problems here. if some1 help me to solve this problem.
1. i can ping server
2. i was unable to ntpq -p (time out, no response from remote server, it looks... (2 Replies)
Hi,
I have 4 machines and all are NTP configured with same ntp.conf file. But 3 machines are in sync with Time server and 4th machine is not contacting & sync with the NTP server. Please see the below details.
# service ntpd stop
Stopping ntpd: ... (0 Replies)
Hi,
I have edited the /etc/inet/ntp.conf file to point to a new time server. When I restart ntp on Solaris 10 using 'svcadm disable/enable ntp' it still points to the old ntp server when I run a 'ntpq -p'.
Any ideas?
Thanks.
Sparcman (4 Replies)
Hi,
I'm having problem with my DNS and NTP.
For the DNS:
I'm using RHEL4, Bonding and heartbeat.
Bond0 IP address: 192.168.1.10
Heartbeat or Bond0:0: 192.168.1.50
Currently, I use my heartbeat ip address for my DNS or in named.conf
Everytime I reboot my server, it says that dns/named... (3 Replies)
I got an ntp time problem on AIX server.
os version is AIX7.1
OS LEVEL 7.1.0.0
i got below output,when i run the below command
bash-3.2# ntpdate -dv XXXXXXXXXXXXXXXXXXXXXXXX
4 Dec 12:50:49 ntpdate: 3.4y
transmit(xxxxxxxxx)
receive(xxxxxxxxx)
transmit(xxxxxxxx)
receive(xxxxxxxxx)... (9 Replies)
Hi,
I have two ntp servers in my cluster and I want all the nodes in my cluster to sync with either of the ntp servers or just one. Unfortunately it keep rotating the sync, between my ntp server 1, ntp server 2 and local. Is there anyway I can change the sync to avoid local?
# ntpq -p
... (3 Replies)
Someone, please help on this issue:-
Note : for security reason i didn't mention hostnames and ips.
==============================================================================
# ntpstat
unsynchronised
polling server every 1024 s
Ntpstat showing unsynchronised.
... (29 Replies)
Discussion started by: shanmugaraj
29 Replies
LEARN ABOUT CENTOS
cups-browsed.conf
cups-browsed.conf(5)cups-browsed.conf(5)NAME
cups-browsed.conf - server configuration file for cups-browsed
DESCRIPTION
The cups-browsed.conf file configures the cups-browsed daemon. It is normally located in the /etc/cups directory. Each line in the file can
be a configuration directive, a blank line, or a comment. Comment lines start with the # character.
DIRECTIVES
The BrowseAllow directive specifies a system or network to accept CUPS browse packets from. The default is to accept browse packets from
all hosts when BrowseRemoteProtocols uses the CUPS protocol.
BrowseAllow 192.168.7.20
BrowseAllow 192.168.7.0/24
BrowseAllow 192.168.7.0/255.255.255.0
The BrowsePoll directive polls a server for available printers once every 60 seconds. Multiple BrowsePoll directives can be specified to
poll multiple servers. The default port to connect to is 631. BrowsePoll works independently of whether CUPS browsing is activated in
BrowseRemoteProtocols.
BrowsePoll 192.168.7.20
BrowsePoll 192.168.7.65:631
BrowsePoll host.example.com:631
The BrowseLocalProtocols directive specifies the protocols to use when advertising local shared printers on the network. The default is
"none". Control of advertising of local shared printers using dnssd is done in /etc/cups/cupsd.conf.
BrowseLocalProtocols none
BrowseLocalProtocols CUPS
The BrowseRemoteProtocols directive specifies the protocols to use when finding remote shared printers on the network. Multiple protocols
can be specified by separating them with spaces. The default is "dnssd cups".
BrowseRemoteProtocols none
BrowseRemoteProtocols CUPS dnssd
BrowseRemoteProtocols CUPS
BrowseRemoteProtocols dnssd
The BrowseProtocols directive specifies the protocols to use when finding remote shared printers on the network and advertising local
shared printers. "dnssd" is ignored for BrowseLocalProtocols. Multiple protocols can be specified by separating them with spaces. The
default is "none" for BrowseLocalProtocols and "dnssd cups" for BrowseRemoteProtocols.
BrowseProtocols none
BrowseProtocols CUPS dnssd
BrowseProtocols CUPS
BrowseProtocols dnssd
SEE ALSO cups-browsed(8)
/usr/share/doc/cups-filters/README
AUTHOR
The authors of cups-browsed are listed in /usr/share/doc/cups-filters/AUTHORS.
This manual page was written for the Debian Project, but it may be used by others.
29 June 2013 cups-browsed.conf(5)