Hi,
Is there a way (either commands/tools/scripts/logic) to compare two given folders on different unix boxes. I want to compare folder a in Unix box 'A' with folder 'b' in Unix box 'B'. I can run the script in Unix box 'A'.
I am looking. for following results:
files/sub folders only in a... (1 Reply)
Hello,
I try to compare 2 folders, i explain, i have file in this 2 folder and i want to print out the difference in this folders...
ex: folder1: file1 file2 file3
folder2: file1 file2
print file3
I do a ls of the 2 folders and i use the command diff (diff $var1 $var2) without... (8 Replies)
I do not know much about shell scripting so I am at a loss here. If someone can help me, that would be great!
I have two directories
/dir1
/dir2
I need to delete all files from /dir1 and that does not have a correspondent file in /dir2. It should NOT check file suffixes in /dir2 . Why?... (20 Replies)
Hi, all:
I've got two folders, say, "folder1" and "folder2".
Under each, there are thousands of files.
It's quite obvious that there are some files missing in each. I just would like to find them. I believe this can be done by "diff" command.
However, if I change the above question a... (1 Reply)
i recently copied 400GB of data from a NTFS drive to a ext4 drive. I want to verify that the data is 100% identical to the original.
I wanted to use cmp but it only does two files. The directory that was copied contains many subdirectories and all sorts of files (not just text).
So I guess... (5 Replies)
Hello again,
A little while back I got help with creating a command to search all directories and sub directories for files from daystart of day x.
I'm wondering if there is a command that I've overlooked that may be able to search for / write folder names to an output file which ideally... (2 Replies)
Hello
I am communicating with two devices using my computer over UDP protocol. The application is running fine. When I monitored the UDP traffic using Wireshark software, I found that there were too many Checksum errors.
Please find attached the png file showing this error. I am about to... (0 Replies)
Hi,
I need help in shell scripting. If someone can help me, that would be great!
Problem. I want Linux Script to compare two folders and copy missing files.
Description.
I have two directories
/dir1
/dir2
I need to copy all distinct/new/unique/missing files from /dir1 and that... (1 Reply)
Hi,
So i know we use cp -r as a basic to copy folders/files.
I would like this BUT i would like to show the output of the files being copied.
With the amazing knowledge i have i have gone as far as this:
1) find source/* -exec cp -r {} target/ \;
2) for ObjectToBeCopied in `find... (6 Replies)
Hello, my first thread here.
I've been searching and fiddling around for about a week and I cannot find a solution.:confused:
I have been converting all of my home videos to HEVC and sometimes the files end up smaller and sometimes they don't. I am currently comparing all the video files... (5 Replies)
Discussion started by: Josh52180
5 Replies
LEARN ABOUT ULTRIX
diff3
diff3(1) General Commands Manual diff3(1)Name
diff3 - 3-way differential file comparison
Syntax
diff3 [-ex3] file1 file2 file3
Description
The command compares three versions of a file, and publishes the ranges of text that disagree, flagged with the following codes:
==== all three files differ
====1 file1 is different
====2 file2 is different
====3 file3 is different
The type of change needed to convert a given range of a given file to some other is indicated in one of these ways:
f : n1 a Text is to be appended after line number n1 in file f, where f = 1, 2, or 3.
f : n1 , n2 c
Text is to be changed in the range line n1 to line n2. If n1 = n2, the range may be abbreviated to n1.
The original contents of the range follows immediately after a c indication. When the contents of two files are identical, the contents of
the lower-numbered file is suppressed.
Options-3 Produces an editor script containing the changes between file1 and file2 that are to be incorporated into file3.
-e Produces an editor script containing the changes between file2 and file3 that are to be incorporated into file1.
-x Produces an editor script containing the changes among all three files.
Examples
Under the -e option, publishes a script for the editor that incorporates into file1 all changes between file2 and file3 - that is, the
changes that would normally be flagged ==== and ====3. Option -x (-3) produces a script to incorporate only changes flagged ==== (====3).
The following command applies the resulting script to `file1':
(cat script; echo '1,$p') | ed - file1
Restrictions
Text lines that consist of a single `.' defeat -e.
Files
/tmp/d3?????
/usr/lib/diff3
See Alsocmp(1), comm(1), diff(1), dffmk(1), join(1), sccsdiff(1), uniq(1)diff3(1)